User manual ICOM IC-E2820

[. . . ] INSTRUCTION MANUAL iE2820 DUAL BAND FM TRANSCEIVER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom product. The IC-E2820 DUAL BAND FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] eRotate [DIAL] to select "RX MESSAGE, " then push [MAIN·BAND]. · The received message with the call sign is displayed in RX MESSAGE screen. rPush [BACK](V/MHz·SCAN) (Right band's) twice to return to function guide indication. tPush [BACK](V/MHz·SCAN) (Right band's) three times to return to frequency indication. 5 DV MODE OPERATION (Optional UT-123 is required) D Voice memory recording for automatic reply IMPORTANT!Set the transceiver for single band operation and/or set minimum [VOL] level for sub-band when recording the reply voice. Otherwise received audio or unwanted noise from subband is also recorded into the voice memory. wPush [MENU](V/MHz·SCAN) (Right band's) to display the "MENU" screen. eRotate [DIAL] to select "DV VOICE MEMO, " then push [MAIN·BAND]. rRotate [DIAL] to select "REPLY VOICE, " then push [MAIN·BAND]. Automatic reply function The automatic reply function replies to calls by a station that specified your call sign. Two methods of replying are available: one is making a reply call with your own call sign, and other one is making a reply call with reply voice audio that has been recorded in DV voice memory. D Automatic reply function setting q Push [F· ] to display the function guide. wPush [MENU](V/MHz·SCAN) (Right band's) to display the "MENU" screen. eRotate [DIAL] to select "DV SET MODE, " then push [MAIN·BAND]. rRotate [DIAL] to select "AUTO REPLY, " then push [MAIN·BAND]. VOICE : Reply to the call with the recorded voice memory. · Bar meter is displayed when the reply voice has already been recorded. tWhile pushing and holding [PTT], speak into the microphone. · Up to 10 seconds of message is recordable. · The recording stops after 10 second or when [PTT] is released. yPush [BACK](V/MHz·SCAN) (Right band's) three times to yPush [BACK](V/MHz·SCAN) (Right band's) three times to return to frequency indication. 55 exit from DV VOICE MEMO screen. DV MODE OPERATION (Optional UT-123 is required) D Play-back or erase the voice memory q Push [F· ] to display the function guide. wPush [MENU](V/MHz·SCAN) (Right band's) to display the "MENU" screen. eRotate [DIAL] to select "DV VOICE MEMO, " then push [MAIN·BAND]. rRotate [DIAL] to select "REPLY VOICE, " then push [MAIN·BAND]. tTo play-back the recorded reply voice, push [](LOW·PRIO). · Push [||](LOW·PRIO) to pause, push [](TONE·DUP) to cancel the play-back. 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 56 EMR communication The EMR communication mode is available for digital mode operation. When an EMR communication mode signal is received, the audio (voice) will be heard at the specified level even the volume setting level is set to minimum level, or digital call sign/digital code squelch is in use. ePush [MENU](V/MHz·SCAN) (Right band's) to display the "MENU" screen. rRotate [DIAL] to select "DV SET MODE, " then push [MAIN·BAND]. t Rotate [DIAL] to select "EMR, " then push [MAIN·BAND]. [. . . ] erroneous information. · Select low microphone sensitivity in set mode. 114 Fuse replacement If the fuse blows or the transceiver stops functioning, find the source of the problem if possible, and replace the blown fuse with a new, properly rated one (FGB 20 A) as shown at right. 20 A fuse 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 130 16 MAINTENANCE Optional UT-123 installation IMPORTANT!Turn power OFF and disconnect the transceiver from power source before opening the top cover. [. . . ]