User manual ICOM CS-F3G PROGRAMMING MANUAL
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ICOM CS-F3G. We hope that this ICOM CS-F3G user guide will be useful to you.
Manual abstract: user guide ICOM CS-F3GPROGRAMMING MANUAL
Detailed instructions for use are in the User's Guide.
[. . . ] PROGRAMMING MANUAL
CLONING SOFTWARE
CS-F3G
FOREWORD
This manual explains in detail how to program each of the functions in the IC-F3GT/GS and IC-F4GT/GS VHF AND UHF TRANSCEIVERS with the CS-F3G CLONING SOFTWARE. The CS-F3G can be set up to meet any number of requirements of your customers, such as system conditions, channels, frequencies, tones, etc.
IMPORTANT
Before using the program, make a backup copy of the original disk. Operate the program using the backup and keep the original in a safe place.
TABLE OF CONTENTS
FOREWORD . 5683
14-1 14-2 14-3 14-4 14-5 14-6 14-7 EXAMPLE EXAMPLE EXAMPLE EXAMPLE EXAMPLE EXAMPLE EXAMPLE 1 2 3 4 5 6 7 . [. . . ] These 5-tone codes are programmed in TX Code in 10-2 TX-CODE CHANNEL (p. Go to TX Code · 5Tone Signaling-- Pos Selects the own ID code sending sequence from OFF, BTM and TOP. TOP : Sends the ID code before sending station or group code.
· ID code sending sequence diagram BTM 12345 12345 12345
ID code
· 5Tone Signaling-- Long Click the check-box to activate the long tone capability for each 5-tone code, RPT, STN and ID, respectively.
-The " " mark appears when long tone is activated.
The time period for the long tone is programmed in the Long Tone Timer in 10-5 5TONE SETTING (p. Go to Long Tone Timer · RX C-No Click the check-box to select the receive 5-tone code channel to be decoded. Up to 8 codes/channels can be selected to decode in each operating channel. Go to RX Code · RF PWR Selects transmit output power for initial setting from High and Low. The selected output power setting for each channel can be switched to either temporary or permanent operation, according to the setting in the RF Power Selection in 3-1 KEY & DISPLAY ASSIGN (p. The [High/Low] switch is assigned in the 3-1 KEY & DISPLAY ASSIGN (p. 7) Go to RF Power Selection Go to High/Low
29
Repeater code Station/Group code (if available)
TOP
12345
Repeater code (if available)
Time
12345
ID code
12345
Station/Group code
5
SCREEN MENU OPERATION-- PMR
· Lock out Selects transmission lock out (temporary transmission inhibit) capability from OFF, Busy, Rpt 1 and Rpt 2. Busy : [PTT] switch cannot be activated while the operating channel/repeater is in use. Rpt1 : [PTT] switch can be activated while receiving a signal with matched CTCSS (or DTCS) tone or no signals. Rpt2 : [PTT] switch can be activated while receiving a signal with matched CTCSS (or DTCS) tone or no signals while 5-tone mute is released, or receiving an unmatched CTCSS (or DTCS) tone while 5-tone mute is activated. In addition, [PTT] switch is not activated for an extra time period in the case of when the lockout penalty timer, programmed in the Lockout Penalty Timer in 33 COMMON 2 (p. 15), is activated even if the transceiver in a transmittable condition. Go to Lockout Penalty Timer · Log IN/OFF Selects automatic ID transmission condition in relation to [PTT] switch from OFF, L-IN, L-INA, L-INI, L-OFF, LOFFA, Both, BothA1 and BothA2. L-INA : ID is transmitted when [PTT] is pushed while 5-tone mute is released.
30
: ID is transmitted when [PTT] is pushed while 5-tone mute is activated. Voice transmission is impossible while 5-tone mute is activated and `SGL' is selected in CH Mute (p. L-OFFA : ID is transmitted when [PTT] is released while 5-tone mute is released. BothA1 : ID is transmitted when both [PTT] is pushed and released while 5-tone mute is released. BothA2 : ID is transmitted when both [PTT] is pushed and released while 5-tone mute is released. ID is transmitted when [PTT] is pushed while 5-tone mute is activated. Voice transmission is impossible while 5-tone mute is activated and when `SGL' is selected in CH Mute (p. [. . . ] In the RX CODE CHANNEL Enter transceiver's own staion code with the code "E" at the end.
Click to check
Select desired condition.
Select; Bell ABC Aud Mode Scan
: ON or Blink : OFF : Aud : Null
Program the transceiver's own station code with the above condition into the desired channel. 6 In the TX CODE CHANNEL Enter station/group code(s) and the transceiver's own station code into desired TX code channel.
Click to check 13 only. (47 are blank. ) Click to check
Click to check
Both are blank.
88
PAGER/CODE SQUELCH
16
16-1 PAGER FUNCTION-- continued
7. Click to check 13 only (Blank for all the others. )
Select "E".
Click to check 14 only. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM CS-F3G
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM CS-F3G will begin.