User manual GARMIN GET 10 ENGINE TILT ADAPTER INSTALLATION AND CONFIGURATION INSTRUCTIONS

[. . . ] A Printed in Taiwan Determining an Installation Location When you are selecting a location to install the GET 10 adapter, consider the following: · During installation, you connect the GET 10 adapter to the analog gauge (or directly to the engine-tilt sensor), and to the NMEA 2000 network. (4. 4 m) of the analog gauge (or the engine-tilt sensor) to avoid splicing bare wires. Choose a location between the NMEA 2000 backbone and the analog gauge (or the engine-tilt sensor). If you cannot connect the adapter directly to the NMEA 2000 network, add a drop cable. [. . . ] Determine where to connect the GET 10 adapter to your existing NMEA 2000 backbone. To extend the NMEA 2000 backbone, connect a NMEA 2000 backbone extension cable to the side of the disconnected T-connector. Add the included T-connector for the GET 10 adapter to the NMEA 2000 backbone by connecting it to the side of the disconnected T-connector. Connect the NMEA 2000 connector on the GET 10 adapter to the T-connector added in step 3. (Optional) If the GET 10 adapter cannot connect directly to the NMEA 2000 backbone, route a NMEA 2000 drop cable (not included) to the bottom of the T-connector added in step 3. Connect the drop cable to the T-connector and to the NMEA 2000 connector on the adapter. notiCe: If you have an existing NMEA 2000 network on your boat, it should already be connected to power. Do not connect an additional NMEA 2000 power cable to an existing NMEA 2000 network, because only one power source should be connected to a NMEA 2000 network. GET10InstallationandConfigurationInstructions Connecting the GET 10 Adapter to an Existing NMEA 2000 Network GET10adapter NMEA000device(notincluded) Dropcable(optional-notincluded) T-connector(oneincluded) ExistingNMEA000network note: This section provides specific configuration information for the GET 10 adapter using your compatible Garmin display device. To access the NMEA 2000 configuration menu on your display device, consult the documentation provided with your display device. Configuring the GET 10 Adapter Calibrating the Engine Tilt To use the GET 10 adapter, you must calibrate the tilt of the engine with which the adapter is associated. 1. Select an option: · For most Garmin chartplotters, select Review > Engine Tilt Calibration. · For other Garmin marine devices, select Config > Engine Tilt Calibration. Select OK when the calibration is complete. Configuring the Engine Number If your boat has multiple engines, you can indicate which engine each GET 10 adapter is associated with. 1. Select an option: · For most Garmin chartplotters, select Review > Engine Number. · For other Garmin marine devices, select Config > Engine Number. Select Done. GET10InstallationandConfigurationInstructions Troubleshooting the Gauge Type When connected to a gauge, the GET 10 adapter gauge type is set to auto Detect by default, and the adapter automatically detects the type of gauge it is connected to. If the engine-tilt reading on a connected Garmin chartplotter or marine instrument changes with the engine RPM, the adapter may be detecting the wrong type of gauge. To test the gauge-type setting: 1. If the engine-tilt reading changes with the engine RPM, change the gauge type. Select an option: · For most Garmin chartplotters, select Review > Gauge Type. · For other Garmin marine devices, select Config > Gauge Type. Select an option: · To automatically detect the gauge type, select Auto Detect. Perform the gauge-type setting test. Configuring the GET 10 Adapter if the Engine Tilt Calibration, Engine Number, and Gauge Type Selections Are Not Displayed Depending on the version of software loaded on your Garmin marine instrument, the specific configuration options may not be displayed on the configuration screens. To calibrate the engine tilt if the menu option is not displayed: To use the GET 10 adapter, you must calibrate the tilt of the engine that the adapter is associated with. 1. Select an option: · For most Garmin chartplotters, select Review > Generic Config. [. . . ] Select Yes. GET10InstallationandConfigurationInstructions Specifications Physical Weight: 12. 85 oz. (365 g) Size: (W × H × L) 31/32 × 43/64 × 3 3/32 in. (4. 9 m) Case Material: Thermoplastic rubber (PCB overmold); PVC jacket (cable); PVC overmold (connectors/strain reliefs). temperature Range: From 5°F to 158°F (from -15°C to 70°C) Compass Safe Distance: 2 in. [. . . ]