User manual FOSTEX X-28

[. . . ] Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. Follow Instructions - All operating and use instructions should be followed. Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like. [. . . ] This means that the sound data has been copied (or moved) to the clipboard, and that the system is ready to proceed to the following paste process. The recorder is ready to paste if there is no problem with the COPY/CLIP (or MOVE/CLIP) process. At this stage, it is possible to check the sound data in which COPY/CLIP (or MOVE/CLIP) was executed. To check the data on the clipboard, refer to the instructions described in "Checking Data in the Clipboard". 6. Use the [CH STATUS/CH SEL] key to select the paste destination track. · There is no need to select a track when pasting on the same track. · The mono track is the only track in which the paste destination can be changed. The other condition in which the paste destination can be changed is when the data from two tracks (odd and even) next to each other (1-2, 3-4, 5-6, 7-8, etc. ) are copied (or moved) on the clipboard. The paste destination track can be changed by pressing the [CH STATUS/CH SEL] key in this case. 73 · Note that it is not possible to paste to the same track that was copied (or moved) when copying (or moving) multiple tracks (1-3, 5-8, etc. ), although it was possible in the cases described earlier. In this case, the track will not be changed even if the [CH STATUS/CH SEL] key is pressed. UNDO/REDO Paste Copy & Paste or Move & Paste can be undone and redone with the UNDO/REDO feature. · The data pasted can be undone (unpasted) by pressing the [UNDO/REDO] key after Copy & Paste (or Move & Paste). · Data pasted but undone (unpasted) can be redone (repasted) by pressing the [UNDO/REDO] key immediately after undoing the paste process. The data will return to the postpaste status when re-done (re-pasted). Both mono tracks and multiple tracks can be erased, as in the case described to the left. However, the REC END point may not move forward (Refer to <Precautions> on this page for more details) even when erasing data on multiple tracks that are not mono tracks or all tracks. Note that the disk space remaining increases as in the case to the left, after data is erased from a section. AUTO PUNCH IN point Any real track (REC END) AUTO PUNCH OUT point AUTO PUNCH OUT point Erase Silence <Precautions Upon Erasing Data> As in the case below, if data is recorded on real tracks 1 to 7, and data is erased from tracks 1 and 2, then the REC END, which the X-28 recognizes, remains the same before and after erasing data. AUTO PUNCH OUT point AUTO PUNCH IN point (REC END) On the other hand, if data is erased from tracks 3 to 7 as shown in the figure below, the REC END point after erasing data will be positioned at the REC END point of tracks 1 and 2. In other words, the REC END point prior to erasing data moves, after the data is erased. AUTO PUNCH IN point AUTO PUNCH OUT point Any real track Any real track (ABS 0) Erase (REC END) (ABS 0) Erase Silence Silence Silence Silence Silence (REC END) Any real track Silence Silence (ABS 0) (REC END) Any real track (ABS 0) (REC END) Erasing Data 1. Set the starting point and ending point of the section to erase. Set the starting point to erase to the [AUTO PUNCH IN] key, and the ending point to erase to the [AUTO PUNCH OUT] key. For more details on setting data to the memory key refer to page 34. 2. Use the [CH STATUS/CH SEL] key to select the track to erase. Mono tracks or multiple tracks (including all real tracks) can be selected to ERASE. Press the [ENTER/YES] key. "Sure?" flashes. UNDO/REDO Erase The erase procedure can be undone and redone with the UNDO/REDO feature. * Data eased can be undone (unerased) by pressing the [UNDO/REDO] key after ERASE. Press the [ENTER/YES] key once again. The erase process will takes place. "Wait Erasing!" flashes on the display while data is being erased. "Completed!" lights up on the display when the data is successfully erased. * The data erased but undone (unerased) can be redone (reerased) by pressing the [UNDO/REDO] key immediately after undoing the erase process. [. . . ] Wait until the X-28 display changes to the Normal display from the start-up display, and then you are ready to operate the CD-1A. 145 Opening/closing the tray · To open the tray, press the eject switch lightly. Pressing the switch will open the tray slightly. Then pull out the tray gently by hand to fully open it. Placing/removing a disc The following are some notes on placing and/or removing a disc. <IMPORTANT!> When placing a disc on the tray, support the tray from the bottom by your hand. If you push the disc to fit into the pivot on the tray without supporting the tray, the tray/drive may be damaged or broken. Also note that the disc must be pushed until it clicks so that it is locked into the pivot securely. [. . . ]