User manual FOSTEX SPA11

[. . . ] Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. Follow Instructions - All operating and use instructions should be followed. Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like. [. . . ] Sure?", asking you confirm. 2 Use the [JOG] dial to highlight the desired program and then press the [SETUP/F1] key while holding down the [SHIFT] key. <Hint> You may use the [CURSOR ] to highlight "DELETE" and press the [ENTER/YES] key to bring up the screen above, instead of pressing the [UNDO/REDO/F3] key while holding down the [SHIFT] key. Deleting a program You can delete an unnecessary program individually. To make recording or editing, a certain amount of disk space is needed. By deleting unnecessary programs, the available disk space increases. 3 Press the [ENTER/YES] key while holding down the [RECORD] key. The selected (highlighted) program is deleted, and the following programs in the list move up. 4 Press the [EXIT/NO] key to switch to the Normal screen. The previous program of the deleted program is selected. <Notes> · When only one program (P01) exists, if you try to delete the program, the data in the program is deleted but P01 remains. · For example, when five programs (P01 through P05) exist, if you delete P03, it looks like P05 is deleted. In other words, P04 and P05 become P03 and P04 respectively. P02 P03 P04 P03 is deleted. Editing a program title You can edit a program title anytime by following the procedure below. Note that you can also enter a program title in the process of creating a new program as mentioned earlier. P01 P05 1 Press the [TRACK EDIT/PGM] key while holding down the [SHIFT] key. The screen for selecting, renaming or deleting a program appears. In the screen, all existing program numbers and titles are shown. P01 P02 P03 P04 Note that you cannot undo or redo deleting the program. 62 Recorder Functions 2 Use the [JOG] dial to highlight (select) the desired program and then press the [TIME BASE SEL/F2] key while holding down the [SHIFT] key. Now you can edit the title of the selected program. The leftmost character of the selected program is flashing. You can put a title name with up to 16 characters from among those listed below. When selecting a character, rotating the [JOG] dial while holding down the [SHIFT] key jumps among characters surrounded with the box below. Flashing <Hint> You may use the [CURSOR ] to highlight "RENAME" and press the [ENTER/YES] key to bring up the screen above, instead of pressing the [TIME BASE SEL/F2] key while holding down the [SHIFT] key. 4 Press the [ENTER/YES] key after editing/entering the title. The edited/entered title is set. 5 Press the [EXIT/NO] (or [STOP]) key. The display returns to the Normal screen. 3 Use the [CURSOR / ] keys to move the flashing (editing) point and use the [JOG] dial (or [CURSOR / ] keys) to select a character for the flashing point. Track editing Because the SPA11 uses a 3. 5-inch E-IDE hard disk as the recording media, you can make non-linear and nondestructive audio editing by track effectively. Copy & Paste The Copy & Paste function allows you to copy track data of a desired part and paste it to a desired part of the same or different track. The copied data remains after pasting the data, so you can paste the data as many times as required. If you try to perform the paste operation when there is not enough disk space, The display will show "Over Time!", as well as the short time. In such a case, shorten the copy (or move) data by the amount more than the displayed time or delete unnecessary sections or programs to keep the enough space, and then try to paste again. 6 Use the [CURSOR ] key to highlight the field ("01" above) for the number of times for repeat paste, and press the [ENTER/YES] key. "01" starts flashing and you can now enter the number of times for repeat paste. Undo/redo of Copy & Paste You can undo a copy & paste or move & paste operation, as well as redo it (undo the undo operation). · By pressing the [UNDO/REDO] key after completing the copy & paste (or move & paste) operation, you can return the track(s) to the condition before performing the copy & paste (or move & paste) operation. · By pressing the [UNDO/REDO] key just after performing the undo operation, you can undo the undo operation and return the track(s) to the condition after performing the copy & paste (or move & paste) operation. Note the following for performing the undo/redo operation. 7 Use the [JOG] dial to select the desired number and press the [ENTER/YES] key. You can select any number between "01" and "99". <Note> Basically you can select the number of times for repeat paste between 1 and 99, however, if the recordable space of the hark disk is limited, you may not be able to select the desired number. The SPA11 automatically calculate the available space and limit the number of times to the appropriate value. When setting the number of times for repeat paste to 02, the copy & paste function is performed as below. Copy & paste within the same track. <Notes> You can undo or redo only when the recorder is stopped. If you carry out any of the following after performing the copy & paste (or move & paste) operation, you cannot undo/redo the copy & paste (or move & paste) operation. Letting the recorder run in playback (or recording) mode and pass through the auto punch-in point while the auto punch mode is active 4. Performing any of the program operations (select, rename or delete). A A' A'' Copy & paste between different track. A' START Point END Point TO Point A'' 65 Recorder Functions Erasing track data You can erase a desired part of track data. You can select a track or tracks (of which you are going to erase data) from among each individual track, each pair of tracks, 1-6 and 1-8. ABS 0 REC END 4 Use the [JOG] dial to select the track(s) to be erased. Rotating the [JOG] dial changes the options among 1 through 8, 1&2, 3&4, 5&6, 7&8, 1-6, and 1-8. The corresponding [TRACK STATUS/TRACK SEL] key(s) of the selected track(s) light in red. 5 Press the [ENTER/YES] key after selecting the track(s). The screen shows the Start and End points. Erase START Point END Point <Notes for the erase function> · When all eight tracks (1 through 8) are recorded, if you erase a part of the chosen track, only the erased part becomes silent (no audio) and the following material does not move advance to fill the gap. [. . . ] Retain the cover which will be used later. 3 Insert the CD-1A unit to the SPA11 as shown below. Carefully insert the CD-1A to the SPA11 in the right direction, without rubbing it against the SPA11 cabinet. Push the unit carefully and firmly with your both hands, but without excessive force, until you feel the connector of the CD-1A mesh with the internal connector. Connector Cover Insert the CD-1A 4 Blank panel Using the screw (1 pc. ) which tightened the blank panel to SPA11, fix CD-1A to the SPA11 chassis. Fasten the screws without excessive force. 2 Remove the metal fitting by unfastening the retaining screw (indicated by an arrow) inside the CD-1A. Because the screw head is small, use a micro screw driver to carefully unfasten the screw without damaging the head by excessive force. CD-1A 5 6 Fix the cover removed in step 1. Connect the power cable of the SPA11 to an AC main outlet, and turn on the power. Check that the SPA11 starts up and the indicator on the front panel of the CD-1A flashes for a few seconds and then turns off. Do not operate the CD-1A unit the SPA11 display shows the Normal screen after showing the start-up screen. 135 Appendix (Installing the optional CD-RW drive) Opening/closing the tray · To open the tray, press the eject switch lightly. Pressing the switch will open the tray slightly. Then pull out the tray gently by hand to fully open it. Placing/removing a disc The following are some notes on placing and/or removing a disc. <IMPORTANT!> When placing a disc on the tray, support the tray from the bottom by your hand. [. . . ]