User manual FOSTEX DCM100

[. . . ] You can now continuously output the slate tone without keeping holding down the [SLATE TONE] key. The maximum number of files you can create in each partition has increased. (2) (3) (4) FOSTEX CO. 3-2-35, Musashino, Akishima-shi, Tokyo, Japan 196-0021 © PRINTED IN JAPAN JUNE 2007 8289 631 000 FX 453119 2 7 A new method for outputting the slate tone The DCM100 can generate and record the slate tone which can be used for matching the level between the DCM100 and external machine. [. . . ] The maximum number of files you can create in each partition has increased. (2) (3) (4) FOSTEX CO. 3-2-35, Musashino, Akishima-shi, Tokyo, Japan 196-0021 © PRINTED IN JAPAN JUNE 2007 8289 631 000 FX 453119 2 7 A new method for outputting the slate tone The DCM100 can generate and record the slate tone which can be used for matching the level between the DCM100 and external machine. With the earlier version, the slate tone can be output while you keep holding down the [SLATE TONE] key. With Version 2. 0, a new method for outputting the slate tone has been added, which allows you to output the slate tone continuously without keeping holding down the [SLATE TONE] key. For details about the method of recording the slate tone while holding down the [SLATE TONE] key, see page 55 of the original manual. Continuous recording across partitions is now possible. You can now make continuous recording across partitions. The "Auto new part. " item has been newly added to the "SYS SETUP" menu of the MENU mode. By setting this item to "On" (the default is "Off"), you can continue recording across partitions. When the first time you enter the MENU mode, "SYS SETUP>" is highlighted on the screen. You can now make gateway setting The "Gateway" menu item has been added to the "TCP/IP SETUP" menu of the MENU mode. This item makes the DCM100 gateway setting which is necessary for network connection using the DCM100 [ETHER] port. Newly added "Gateway" menu item 2) While "SYS SETUP>" is highlighted, press the [ENTER/YES] key. The display now shows the SYS SETUP menu screen ("SetProjectName" is initially highlighted). How to set "Gateway" 1) While the unit is stopped, press the [ENTER/YES] key to enter the MENU mode. 3) Use the [MENU] dial to select "Auto new part" and press the [ENTER/YES] key. The current setting ("On" or "Off") starts flashing and you can now make On/Off setting (by default, "Off" is selected). 2) Use the [MENU] dial to select "TCP/IP SETUP" and press the [ENTER/YES] key. The display now shows the TCP/IP SETUP menu screen, on which "IP Address>" is highlighted. flashing Off (default) At the point when there is no remaining space left on the current partition, recording ends. At the point when there is no remaining space left on the current partition, the unit continues recording on the next partition. 3) Use the [MENU] dial to select "Gateway" and press the [ENTER/YES] key. The display now shows the current gateway setting (by default, "0. 0"). On 4) 5) Use the [MENU] dial to select "On" (or "Off") and press the [ENTER/YES] key. Press the [STOP] key or [EXIT/NO] key repeatedly to exit the MENU mode. 4) Press the [ENTER/YES] key. The leftmost value of the current setting starts flashing and you can now edit the value. If you do not edit the value, press the [EXIT/NO] key repeatedly to exit the MENU mode. <Hint>: When you start recording with "Auto new part. " set to "On", the following popup window appears for confirmation. 5) Use the [MENU] dial (or the alphanumeric keys) to enter the desired value. You can select the editing point by using the [SKIP/CURSOR >>|] or [SKIP/CURSOR |<<] key. 6) 7) Press the [ENTER/YES] key to confirm your editing. [. . . ] 0"). On 4) 5) Use the [MENU] dial to select "On" (or "Off") and press the [ENTER/YES] key. Press the [STOP] key or [EXIT/NO] key repeatedly to exit the MENU mode. 4) Press the [ENTER/YES] key. The leftmost value of the current setting starts flashing and you can now edit the value. [. . . ]