User manual FOSTEX D824 SERVICE MANUAL

[. . . ] Service Manual Model & MODEL 8345 TC/SYNC CARD MODEL 5042 / 5043 BALANCE I/O CARD MODEL 8350 AES/EBU CARD 16TRACK DIGITAL RECORDER 8TRACK DIGITAL RECORDER CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. Read instructions - All the safety and operating instructions should be read before the appliance is operated. Retain instructions - The safety and operating instructions should be retained for future reference. [. . . ] The display indicates the free audio file numbers. OL 0 3 6 9 12 18 24 30 42 44. 1kHz _ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 If the Free Block indicates a large number even after formatting and no signal is recorded or recorded signal on the EIDE HDD is frequently skipped, the diskette / hard disk drive can be judged to be in a bad condition. 4-10. When this menu is selected, pressing the [EXECUTE/YES] key would output the current time information in the shape of FEX (Fostex System Exclusive message) from MIDI OUT port. The internal RTC on the D1624/D824 which receives the information can be set to the current time. : Blinking OL 0 3 6 9 12 18 24 30 42 44. 1kHz _ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 21 D1624 / D824 5. ERROR CODE LIST The chart below indicates the error code number and corresponding description. Since the error code list is basically designed for our engineers to improve the software, the description is quite technical. If you find the D1624/D824 with one of the error codes displayed, we encourage you to update the software first. In case updating the software does not solve the problem, we would like you to inform us about details. D1624/D824 ERROR CODE LIST ERROR CODE 1 9 10 11 12 14 15 16 20 21 22 30 31 32 35 36 40 41 42 45 52 60 61 62 63 64 71 73 96 97 99 DESCRIPTION D-108 tries to access the address which does not exist. When saving system region sector, its address is registered in Free_block File during Free block File checking procedure. Link_pointer which links Audio File indicates smaller address (out of region) than Link_File address region in RAM. Link_pointer indicates larger address (out of region) than Link_File address region in RAM. Link_Pointer during recording/reproducing indicates smaller address (out of region) than actual Link_File address region. Link_Pointer during recording/reproducing indicates larger address (out of region) than actual Link_File address region. "Pointer_addre" calculation of Link_Pointer during recording/reproducing is not correct. src_cash_load: Improper access of link address occurred while PASTE editing. bak_cash_load: Incompatibility problem occurred on program link during PASTE/MOVE editing. non_des_cash_save_sub: Improper access occurred when recording/reproducing. remake_free_block: There was improper access to program management region. remake_free_block: There was improper access to program management region. remake_free_block: There was improper access to program management region. remake_free_block: There is an overlapping section in program management region. There is no enough region to accommodate history of multiple undo file list. There was improper access to program management region when saving System File. [. . . ] R0104~0804 R0105~0805 R0106~0806 R0107~0807 R0108~0808 R0109~0809 R0110~0810 R0111~0811 R0112~0812 R0113~0813 R0114~0814 R0115~0815 R0116~0816 R0908~1608 R0909~1609 R0910~1610 R0911~1611 R0912~1612 R0913~1613 R0914~1614 R0915~1615 R0916~1616 Part No. 8230 5002 23 8230 5005 62 8230 5005 62 Description ST, carbon, 1/10W, 22k, 5% ST, carbon, 1/10W, 5. 6k, 5% ST, carbon, 1/10W, 5. 6k, 5% N/A N/A N/A N/A N/A N/A N/A N/A N/A Ref. C0912~1612 C0913~1613 C0110~1610 C0111~1611 C0112~1612 C0113~1613 Part No. 8232 1422 27 8232 1422 27 8233 5001 01 8233 5001 01 8232 1422 27 8232 1422 27 Description VT, ALU, 10V, 220µF, 20%, SME-VB VT, ALU, 10V, 220µF, 20%, SME-VB ST, CER, 50V, 100pF, 5%, CC20SL ST, CER, 50V, 100pF, 5%, CC20SL VT, ALU, 10V, 220µF, 20%, SME-VB VT, ALU, 10V, 220µF, 20%, SME-VB MISCELLANEOUS Ref. [. . . ]