User manual FOSTEX B-16

[. . . ] Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Grounding or Polarization - The precautions that should be taken so that the grounding or polarization means of an appliance is not defeated. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. [. . . ] Nonuse Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. Damage Requiring Service - The appliance should be serviced by qualified service personnel when: A. Objects have fallen, or liquid has been spilled into the appliance; or C. The appliance does not appear to operate normally or exhibits a marked change in performance; or E. The appliance has been dropped, or the enclosure damaged. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer. Ventilation - The appliance should be situated so that its location or position dose not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. 17. Also note that you cannot use the [USB] and [IEEE1394] ports while the selector is set to "PD-6". 11) [DC OUT (PD-6 ONLY)] connector Used to connect to the [DC IN] connector of the PD-6 using the DC cord supplied with the B-16. Set the selector to this position when exIEEE1394 porting a file recorded on a DVD-RAM USB disk set on the B-16 to your PC. 12) [DC IN] connector Used to connect to the external DC power supply. 13) [AC IN] connector Used to connect to the supplied AC cord. 4 How to stack the PD-6 and B-16 together 1) Remove the blank panel at the bottom of the PD-6. 4) Fix the supplied cushion using the fixing screws which are removed in the previous step. Cushion 2) Replace the two screws for fixing the rubber feet at the bottom of the PD-6 with the screws supplied with the B-16. 5) Pull out the connection cable from inside the B-16. <Note>: Never forget to replace the screws for fixing the rubber feet. Otherwise, the PD6 may malfunction or generate a noise because of imperfect grounding. 3) Remove the two screws for fixing the cover at the top of the PD-6, and open the cover. 6) Put the PD-6 on the B-16 and plug the connector of the cable to the PD-6, as shown below. Make sure to plug the connector in the correct direction. <Note>: The removed screws are used later for fixing the cushion. Be sure not to lose them. 5 7) After connecting the cable, stack the PD-6 on the B-16. After hanging the projection on the PD-6, lift up the fixing angle until it is locked. <Note>: When stacking the PD-6 on the B-16, make sure to perfectly fit the dent of PD-6 rubber feet to the metallic projections of each B-16. Otherwise, the PD-6 may malfunction or generate a noise because of imperfect grounding. 9) Fasten the fixing screw of each fastening. Fasten the fixing screw of each fastening so that the fastening may not be off. Be careful not to apply excessive force. 8) Use the fastenings on both the left and right sides of the B-16 to fastening the PD-6. Pull up the metallic projection of each fastening and hang it on the PD-6. (The following pictures show the example of the left side. ) Confirm both the left and right fastenings are fixed tightly. Now you complete stacking the B-16 and PD-6 together. See the next page. 6 Connecting the power cords To supply power to the PD-6 and B-16, connect the AC and DC cords supplied with the B-16, as shown below. Make connection using the supplied DC cord. This connector is used when using the external DC power supply. Connect to the AC outlet using the supplied AC cord. <Notes> · When the B-16 is connected to the PD-6, turn on the B-16 first, followed by the PD-6. · When the B-16 is connected to the PD-6, make sure that both the PD-6 and B-16 are turned off before you switch the selector (for selecting [PD-6 IEEE1394] or [USB]) on the B-16 front panel. PC connection By connecting the B-16 to your PC regardless of whether the B-16 is connected to the PD6 or not, you can export the B-16 audio file data to your PC. See also the next page for the connection examples. <Notes for using the B-16 with your PC> To use the B-16 with your PC, install the dedicated driver (on the supplied CDROM) or commercially available DVD-RAM writing software to your PC. Also note that even if the dedicated driver (or commercially available DVD-RAM writing software) is correctly installed, the Read/Write functions are limited depending on OS, as below. When using the [USB] port: Windows XP, 2000 --> Macintosh OSX, OS9. 2. 1, OS9. 2. 2 --> Both "Read" and "Write" are possible. [. . . ] Only "Read" is possible When using the [IEEE1394] port: Windows XP, 2000, ME, 98SE --> Macintosh OSX, OS9. 2. 1, OS9. 2. 2 --> Both "Read" and "Write" are possible. Only "Read" is possible. 7 Connecting the B-16 alone to your PC By connecting the B-16 to your PC, you can export an audio file on a DVD-RAM disk set to the B-16. Note that you cannot export an audio file on the B-16 internal HDD. To the IEEE1394 or USB port on your PC <Notes for using> · Set the selector on the B-16 front panel to "IEEE1394/USB". Never use both ports together. Daisy-chaining the PD-6, B-16 and PC By making "daisy chain" of the PD-6, B-16 and PC as shown below, you can export an audio file on a DVD-RAM disk set to the PD-6 or B-16. [. . . ]