User manual FOSTEX 450

[. . . ] Song data of the D2424LVmkII can be saved as an adat or S/P DIF digital signal, as well as can be backed up to the pre-installed CF drive as an FDMS-3 Ver. You can also use the optional E-IDE hard disk drive instead of the pre-installed CF drive for high speed backup of an FDMS-3 Ver. For optional units, Model 8346 TC/SYNC card is available and these will also comply to phasing of the standard feature WORD clock and also phasing against slave control by external LTC and VIDEO reference signals. Please carefully read through this manual together with the separate "Quick Operation Guide" for long and satisfying operation of this equipment. Model D2424LVmkII Reference Manual (Safety Instruction/Contents) CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The following four editing functions allow "Editing of Independent Audio Tracks. " Copy & Paste You can copy a specific range of data from a specific track and paste it to the same or a different track. Copy & Paste is possible in the presently active program or also in a different program. Track Exchange Between tracks 1-56, exchanging is possible in mono track units or group track units (Stereo pair 2 tracks or 8 tracks). Move & Paste You can move a specific range of data from a specific track and paste it to the same or a different track. Editing the track name Any type of track name can be registered and edited for each channel. Move & Paste You can erase a specific range of data from a specific track or all tracks. <Note>: Although Copy & Paste can be executed in a different program, all other editing work can only be done within the currently active program. Consequently, in order to edit the active program, the desired program should be selected before starting to edit. In general, don't change a program until you finish editing except to Copy & Paste to a different program. If editing is started while in another program, you could accidentally lose data. Copy & Paste, Move & Paste, and Erase with the exception of track exchange and editing the track name, is possible only for data recorded on the real track. If data stored in the additional track is to be edited, move it temporarily to a real track, and then edit it. Copy & Paste and Move & Paste Copy & Paste and Move & Paste might seem like the same function. Remember this difference when you start using these functions. · Copy & Paste Using the Copy & Paste function enables you to copy a specific range of data from a specific track to the clipboard as shown below (this is called "Copy Clip" operation on the unit), then paste the data at a specific point in a specific track. The number of copy source tracks and the number of destination tracks are the same. That is, if you copy mono track data, you can paste it to a mono track. If you copy adjacent odd/even tracks (e. g. , track 1 and track 2), you can paste it to adjacent odd/even tracks. At this time, the flashing [RECORD TRACK] indicator becomes continuously lit. Flashing SURE? (8) Press the [EXIT/NO] key or the [STOP] button. The recorder exits edit mode and displays the previous Time Base indication. Flashing (9) OL 0 3 6 9 12 18 24 30 42 Turn off the [RECORD TRACK] select key of the copy (or move) source track. OL 0 3 6 9 12 18 24 30 42 BIT 24 FS kHz CLOCK INT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 · Single Undo/Redo Paste You can single undo or redo a Copy & Paste and Move & Paste operation. · To restore the data that existed prior to the paste operation, press the [UNDO/REDO] key. To restore the pasted data after you undo the paste operation, press the [UNDO/REDO] key again. When you press the [UNDO/REDO] key, the recorder will undo or redo the operation immediately, and display "Undo !" or "Redo !" and "COMPLETED !". Track display ( ) of the item to be copied (or moved) will change to lit. (5) Select a destination track to paste data. · If paste is to be done on the same track, it is not necessary to select the track. · Changing the destination track for paste is permissible to a mono track or adjacent two tracks in odd and even numbers (1-2, 3-4, 5-6, etc. ) only when the copy (or move) data is on the clip board. For this procedure, if the [RECORD TRACK] select key of the track to be changed is pressed, and an objective track for pasting can be selected. · If a multiple number of tracks (1-3, 5-8, etc. ) other than those above had been copied (or moved), paste can be done only to the same track as that of the copy (or move) originating track. The track cannot be selected even though the [RECORD TRACK] select key is pressed. · <Note>: This function only works when this recorder is in the stop mode. <Note>: If you perform one of the following operations after you use the Copy & Paste or Move and Paste operation, the Undo/Redo function will no longer be effective. 1. When a new editing job is executed (such as Copy & Paste, Move & Paste, Erase). While in the AUTO PUNCH ON mode, when the AUTO PUNCH IN point is passed in the PLAY (or RECORD) mode. When multiple undo is executed. (6) Turn the Jog dial to enter the number of repeats (Repeat = **). You can enter up to 99. However, this is automatically limited by the available recording source on the disk. [. . . ] 32, D-55411 Bingen, Germany TEL: (+49) 6721-94330, FAX: (+49) 6721-32046 <SWITZERLAND> NAME: Audio Bauer Pro AG ADD: Bernerstrasse-Nord 182, CH-8064 Zurich, Switzerland TEL: (+41) 1-4323230, FAX: (+41) 1-4326558 <GREECE> NAME: Bon Studio S. ADD: 6 Zaimi Street, Exarchia, 106. 83 Athens, Greece TEL: (+30) 210-3809-605, 606, 607, 608 FAX: (+30) 210-3845-755, 210-3827-868 <UK> NAME: SCV London ADD: 40 Chigwell Lane, Oakwood Hill Industrial Estate, Loughton, Essex IG10 3NY U. TEL: (+44) 20-8418-0778, FAX: (+44) 20-8418-0624 <ICELAND> NAME: I. ADD: ARMULA 38 108 REYKJAVIK, ICELAND TEL: (+354) 588 5010, FAX: (+354) 588 5011 FOR THE US CUSTOMERS ONLY FOSTEX AMERICA LIMITED WARRANTY The following statement defines specific legal rights. [. . . ]