User manual FOSTEX 4035

[. . . ] New UTILITY Menu "Edit Volume Lbl (Edit Volume Label)?" The "VOLUME LABEL" is a name which is used to identify a disk. As mentioned in the 4035 Owner's Manual page 1-5, the default name of VOLUME LABEL to be attached to the DVD-RAM disk is "4035-DVD". This UTILITY menu has been newly added so that the VOLUME LABEL can be changed even after formatting the DVD-RAM disk used on 4035. The followings are the procedures explaining about changing the default VOLUME LABEL "4035-DVD" of the preformatted DVD-RAM disc. 1-1. [. . . ] 2) Rotate the jog dial or press the [SKIP/CURSOR |<<] / [SKIP/CURSOR >>|] key to select the "F. Name MD?" menu. The default File Name Mode is "DATE". The file name with the following characters are not correctly recognized by the Windows OS platform. ", " < ", " > ", " | ", " ¥ ", " - " Remember that the 1st character of the file name must start from an alphabet and the following use only ASCII characters. Although up to 247 numbers of characters can be used as a file name, the maximum number of characters recognized by SDII and BWF specifications are 23 and 55 respectively. 5) Set the 3-digit number. Set the 3-digit number by rotating the jog dial and / or using the 10 alphanumeric keys (001 ~ 999). The input 3-digit number sets the number attached to the default file name. The following example sets the default file name as "4035-005". 10 6) Press the [ENTER/YES] key. Pressing the [ENTER/YES] key sets the default file name as "4035-005". SETUP Flashing 7) Press the [EXIT/NO] key or [STOP] key. "DefaultFileName?" appears again. Pressing the [EXIT/NO] key or [STOP] key goes back to the normal display. By the above procedures, the default file name is set to "4035-005". If the "TAKE" File Name Mode is selected, every time a file is newly created, it will be named as "4035-5", "4035-6", . . . LIST PLAY Function The LIST PLAY function allows to link multiple audio files recorded by the same condition (e. g. TR MODE, Fs, AUDIO FILE) and reproduce the files continuously while maintaining TC continuity. ("?" is flashing. ) Flashing 5) Press the [ENTER/YES] key. "Sure?" message starts flashing. Flashing 6) Press the [ENTER/YES] key. The file is deleted. CAUTION Even after unnecessary files are deleted, they can be restored by the "Restore DelFile?" UTILITY menu. This indicates that the files have not been completely erased from the DVD-RAM disk yet. However, if you optimize the DVD-RAM disk by the "Optimize Disk?" UTILITY menu, deleted files are completely erased from the DVD-RAM disk. After optimizing, they can be no longer restored. NOTE A deleted file before optimizing on 4035 is categorized as a "hidden file". (If the folder option "A hidden files are not displayed. " on the computer is selected, change the folder option setting to allow to display hidden files. ) In the condition that the translucent hidden file can be seen on the computer, display the file property and uncheck the "check mark" on the "hidden file". By doing so, you can restore the deleted file even on the computer. 6-4. Locating to Beginning of PLAY LIST While the LIST PLAY mode is on ([LIST PLAY] key is lit), executing "LOCATE ABS0" (pressing the [<< REWIND] key while holding down the [STOP] key) allows to locate to the beginning of the first linked file (the closest file to the LTC 00h00m00soof). 6-5. Locating to End of PLAY LIST While the LIST PLAY mode is on ([LIST PLAY] key is lit), executing "LOCATE REC END" (pressing the [F FWD >>] key while holding down the [STOP] key) allows to locate to the end of the last linked file. 14 7. Use of PS/2 Keyboard From the V1. 00 software, a PS/2 keyboard can be used to input File Name, Volume Label, etc. Refer to the following explanation and the drawing for the correct usage of PS/2 keyboard. 7-1. Valid and Invalid keys On the current software version, the translucent keys (gray) in the drawing below cannot be used. [. . . ] For example, if 2 x 4035s exist in a single network environment, the IP Address on one of the 4035s must be changed. IP Address The IP Address on 4035 is set in this menu. 1) Rotate the jog dial to select "IP Addr. ?[192. 16" and press the [ENTER/YES] key. SETUP Flashing To check the full digits of IP address, press the [SKIP/CURSOR >>|] key once. If you do so, the following will appear on the 4035 FL display. SETUP Now you can see that the current IP Address setting on 4035 is [192. 168. 1. 64]. 2) Press the [ENTER/YES] key. If the [ENTER/YES] key is pressed, the section "192" starts flashing. SETUP Flashing 3) Move the cursor and change the IP Address. Move the cursor by the [SKIP/CURSOR >>|] or [SKIP/CURSOR |<<] key and rotate the jog dial to change the IP Address. The alphanumeric keys can be also used to change the IP Address. 4) Press the [ENTER/YES] key. [. . . ]