User manual EPSON EMP-7250
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual EPSON EMP-7250. We hope that this EPSON EMP-7250 user guide will be useful to you.
You may also download the following manuals related to this product:
EPSON EMP-7250 (7937 ko)
EPSON EMP-7250 (3324 ko)
EPSON EMP-7250 (3324 ko)
EPSON EMP-7250 (3325 ko)
EPSON EMP-7250 (7908 ko)
EPSON EMP-7250 (6916 ko)
EPSON EMP-7250 (3352 ko)
EPSON EMP-7250 (7925 ko)
EPSON EMP-7250 EMP MONITOR MANUAL (1989 ko)
EPSON EMP-7250 (1578 ko)
EPSON EMP-7250 SETUP GUIDE (1735 ko)
Manual abstract: user guide EPSON EMP-7250
Detailed instructions for use are in the User's Guide.
[. . . ] Important Information
Please read the following important information about your projector.
Important Safety Information
Warning: Never look into the projector lens when the lamp is switched on as the bright light can damage your eyes. Warning: Never open any covers on the projector except the lamp and filter covers. Dangerous electrical voltages inside the projector can cause severe injury. Except as specifically directed in this Owner's Manual, do not attempt to service this product yourself. [. . . ] Connect the plug at the other end of the audio/video cable to the audio output jacks of the video source. For S-Video, insert one end of an S-Video cable into the projector's S-Video connector. Insert the other end into the S-video-out jack of your video source.
S-Video connector
S-Video cable
6. For component, insert three ends of a BNC cable into the projector's R/R-Y, G/Y and B/B-Y jacks. Insert the opposite ends of the cable into the Y/Video, C/R-Y, and B-Y jacks on your component video source. (Don't insert any of the cable ends into the HD/Sync and VD jacks. ) 7.
Note: When the Computer 2/BNC switch is set to BNC, the projector is unable to project the Computer 2 image signal. Note: Use a standard BNC cable, which you can purchase from any computer store. The 5BNC video cable supplied by EPSON as an optional accessory does not work with component video.
ssssss
Connecting to a Computer
31
Connecting to an External Speaker or PA System
Although the projector's internal speakers are enough for most small- or medium-size rooms, you can connect the projector to an external speaker or public address (PA) system for large rooms or to gain maximum benefit from the projector's built-in 3D sound function. To connect the projector to an external sound system, you need to obtain an RCA-to-3. 5 mm stereo audio cable. Connect the cable's 3. 5 mm stereo miniplug to the projector's Audio Out jack.
Audio Out jack
stereo audio cable
3. Insert the cable's red plug into the Audio R jack, and the white plug into the Audio L jack.
Note: The internal speakers are disabled when an external audio system is used.
ssss
32
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
2
Using the Projector
This chapter provides the following information about using
your projector: · Turning the equipment on and off · Focusing and positioning the screen image · Controlling the projector with the remote control and the operation panel · Monitoring the projector's operating status
ssssss
33
The illustration below identifies the parts of your projector.
operation indicator operation panel speaker remoto control receiver
zoom ring focus ring
speaker front foot
foot adjust lever
ssss
34
Turning the Equipment On and Off
Turn on the projector and its attached equipment in the following order. Computer When you turn off the equipment, do so in the reverse order.
Turning the Projector On and Off
1. When you plug in the projector power cord, the power indicator flashes orange for few seconds. If computer or video equipment is attached, the computer or video signal is projected. It is especially important that children are not allowed to look into the lens. Caution: When turning the projector on or off with the remote control, be sure to turn the remote control on first with the power switch.
ssssss
Turning the Equipment On and Off
35
After you press the power button to turn off the projector, a confirmation message appears. The fan will remain on and the operation indicator will flash orange for about one minute as the projector cools down.
operation indicator
When the projector has cooled down, the operation indicator stops flashing and remains orange.
Note: If you press the Power button to turn the projector back on while the operation indicator is orange, there may be a delay before a projected image appears.
ssss
36
Focusing and Positioning the Screen Image
When an image appears on the screen, check that it is in focus and correctly positioned on the screen.
zoom ring
focus ring
· To focus the image, rotate the focus ring (the outer ring on the lens). Rotate the zoom ring clockwise to make the image larger, or counterclockwise to make it smaller.
ssssss
Focusing and Positioning the Screen Image
37
If you need to raise or lower the image on the screen, extend or retract the two feet at the bottom of the projector as follows:
1. Stand behind the projector and support the front of it while you lift the foot adjust levers above the feet. [. . . ] Clean the lens as described in Chapter 5, "Maintenance. " u The colors of the image are not right. If you're displaying a computer image, adjust the red, green, and blue settings in the Video menu. If you're displaying video, adjust the Color and Tint (NTSC only) settings on the Video menu. First check that the volume setting is not turned all the way down and that the audio/video cable is securely attached to both the projector and the audio source. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE EPSON EMP-7250
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual EPSON EMP-7250 will begin.