User manual DOMETIC SLIDE TOPPER INSTALLATION

[. . . ] Product features and specifications as described or illustrated are subject to change without notice. Installation methods not described in this manual must have written approval from Dometic Corporation. RECOGNIZE SAFETY INFORMATION ! This is the safety-alert symbol. When you see this symbol in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating instructions. Important: The slide topper cradle kits 3309526. XXX(X) must be installed with all slide topper awnings over lengths of 198". [. . . ] Note: The 3106992. (X)21(X) mounting bracket kit is used when mounting the slide topper on a slide out room that is not flush to the side of the coach. 1" Max. Mounting Bracket (Kit # 3106992. X21X) Awning Rail Top Flange of Room 6" Min. 5. 25 inch Max. Slide-Out Room Flange or Facing 0. 74" Mounting Bracket Side Flange of Room FIG. 2 Mounting Bracket Position Bracket adjacent to top and side flanges as shown. FIG. 3 Mounting Bracket (Kit # 3106992. X39X, . X54X & . X62X) Awning Rail Top Flange of Room 6" Min. 5. 25 inch Max. Slide-Out Room Flange or Facing 1. 24" Mounting Bracket Side Flange of Room Mounting Bracket Position Bracket adjacent to top and side flanges as shown. 4 Slide Topper Installation & Operating Instructions FIG. 4 Mounting Bracket (Kit # 3106992. X47X, . X70X, 088X & 096X) Awning Rail Top Flange of Room 4" Min. 3. 5" Max Slide-Out Room Flange or Facing 1. 24" Mounting Bracket Position Bracket adjacent to top and side flanges as shown. Z-Clip Mounting Bracket Side Flange of Room When installing the A&E model Slide-Topper on vehicles with extra large slide-out room flanges, it may be necessary to install the mounting bracket directly on the flange. 5 & 6. The bracket must only be mounted on the flange where there is sufficient backing material or framing behind the flange. FIG. 6 5 Slide Topper Installation & Operating Instructions OPTIONAL 3107940. 003 SPACER KIT Used when Slide-out flange has a large curve or is recessed behind the main wall of vehicle. SOME INSTALLATIONS MAY REQUIRE USE OF SPACER KIT 3107940. 003 FIG. 8 SOME INSTALLATIONS MAY REQUIRE USE OF SPACER KIT 3107940. 003 SIDE WALL WITH RECESSED SLIDE-OUT SHOWN FIG. 7 3106992. 039X BRACKET SHOWN 3106992. 047X BRACKET SHOWN 0. 75" SPACER KIT SHOULD ALSO BE USED WHEN SLIDE-OUT ROOM WALL LIES BEHIND MAIN WALL OF VEHICLE 1. 24 0. 75" SPACER KIT SHOULD ALSO BE USED WHEN SLIDE-OUT ROOM WALL LIES BEHIND MAIN WALL OF VEHICLE 1. 24" PREPARATION: Unpack the awning and check the contents against the following parts list: (2) 308171. 022 Pop Rivet (3/16" x 3/8") *730099-(X) Awning Rail - Required *3107216. 008 Screw, Awning Rail, S 6-20 x 0. 50" Sq Dr **(1) 3106992. X21(X) Std Wall Brkt W/Anti-Billow **(1) 3106992. X39(X) Offset Wall 60° Brkt W/Anti-Billow **(1) 3106992. X47(X) Offset Wall 90° Brkt W/Anti-Billow **(1) 3106692. X70(X) Offset Wall 90° Brkt W/Anti-Billow (1) 3106992. 088(X) Offset Wall 90° W/Steel Hex Bars & Anti-Billow (1)3106992. 096(X) Offset Wall 45° W/Steel Hex Bars & Anti-Billow *(2) 3309962. 003(X) Bracket Spacer NOTE: Replace (X) with color letter code B = Polar White H = Mende S = Satin R = Champagne U = Black V = Gold * Not included with all models ** Not included but one of the 3 options required. INSTALLATION INSTRUCTIONS ASSEMBLE EXTENSION 2. Rivet both extensions into the end brackets using the two (308171. 022) 3/16 x 3/8" pop rivets. Unwind ONLY ONE wrap of the awning to allow easy insertion into the awning rail. Do Not remove cotter pins until instructed to do so by these instructions. INSTALL AWNING RAIL 1. See figure 2, 3, 4 and 9 to determine the correct location for the awning rail. Apply a sealant to the back edge of the awning rail to prevent leaks, and install the awning rail using the (3107216. 008) #6 x 1/2" screws or equivalent. The awning can be assembled and held in location to check for conflicts with flashing. 6 Measure From Bottom Of Awning Rail Mounting Distance Measure From Inside Edge Of Slide-Out Room Frame. MOUNTING DISTANCE MNTG BRKT 3106992. X21X 6" - 7" MNTG BRKT 3106992. X39X 6" - 7" MNTG BRKT 3106992. X47X 4" - 5" MNTG BRKT 3106992. X70X 6" - 7" MNTG BRKT 3106992. X88X 4" - 5" MNTG BRKT 3106992. X96X 6" - 7" Slide Topper Installation & Operating Instructions FIG. 10 Note: The Z-Clip brackets and oscar rivets (not supplied) should be used when brackets are installed on laminated walls and are required when using the 90° wall brackets. 12 Z-Clips Install Screws Z-Clips 90° Bracket Shown ALIGN FABRIC 4. [. . . ] If the vehicle has a fiberglass wall, use Oscar rivets (not supplied) instead of 3105445. 005 #10-12 x 0. 75" screws. Install edge protector (not supplied) on each end of slideout-room molding. Allow protector to extend beyond edge of molding by 1/4" to 1/2". Note: Not all installations will be able to use a Dometic edge protector. [. . . ]