User manual DENON RCD-N7

[. . . ] Following the provisions of 73/23/EEC, 89/336/EEC and 93/68/EEC Directive. · Never disassemble or modify the set in any way. 2 , , · Do not obstruct ventilation holes. the · The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. · No naked flame sources, such as lighted candles, should be placed on the apparatus. · Please be care the environmental aspects of battery disposal. [. . . ] Press the ENTER/ MEMO button on the remote control unit to store the input character. · Press the 7 button or the ENTER/ MEMO button to store the input character. · You can move the cursor backward by pressing the 6 button to make corrections. Press the EDIT button to confirm the names of the preset stations. . 2 Flashes 2 ENTER/MEMO Use the "9" and "8" buttons to select preset number "3" or press the "3" button on the numeric keypad to display preset number "P03". · The "9" and "8" buttons on the main unit can be selected when the preset mode has been set. (Press the 2/BAND and + buttons at the same time to change the Preset mode. ) 3 Main unit Remote control unit Remote control unit Next Flashes Using the RDS functions (This operation is only possible from the remote control unit. ) 4 Receiving RDS broadcasts (FM only) 5 Press the 9 /8 button on the remote control unit to tune in the desired preset number. 1 Press the BAND button and set the FM AUTO. Main unit Remote control unit 6 Press the ENTER/ MEMO button to confirm the preset station number. 2 Press the RDS button. · To change a preset station name, press the CH+(9)/ CH­(8) to display the preset station you want to change, then press EDIT and use the same procedure as in step 3 above to change. · To preset only the frequency of the radio station, start over from step 1. The display shows the preset number, band and frequency. 3 Press the TU+(7 ) or TU­(6) button. (auto tuning) Reception frequency 4 The station is tuned in. NOTE: If no RDS station is found, " NO PROGRAM " is displayed. 13 PTY Search TP Search 1 Press the RDS button twice. 1 Press the RDS button 3 times. 2 Press the PTY button to select the type of program. (One of the 29 types listed below can be selected. ) 2 Press the TU+(7 ) or TU­(6) button. (auto tuning) Reception frequency 3 Press the TU+(7 ) or TU­(6) button. The borderline flashes. qData Label Segment Text data included in the broadcast is scrolled. eProgram Type The category of the currently tuned in station is displayed. rEnsemble Name 1 wStation Order Use 9/8 buttons to change the order of the entries on the service list created using the "AUTO SCAN" function. If the mark is to the right of the borderline, there is little noise in the sound being received. 2 The ensemble name is displayed. ySignal Quality The sensitivity of the reception signal (0 to 100) is displayed. uAudio Information The bite rate and mode of the currently tuned in station is displayed. · The timer clock can be set using the MENU/SET button. <MULTIPLEX> By order of frequency (Default) <ALPHANUMERIC> In alphabetical order eDynamic Range Control Use 9/8 buttons to switch the dynamic range. <OFF> <1> rDAB Version <1/2> The DAB module's version is displayed. 16 11 USING THE TIMER The time and timer functions are incorporated in the CD receiver. Timer Settings Types of timer operations EVERYDAY TIMER : Use this to turn the power on and standby at the same time every day. SLEEP TIMER : Use this to set the power to turn standby after 10 to 90 minutes, in steps of 10 minutes (operated from the remote control unit). Notes on timer settings · Be sure to set the current time beforehand. · To listen to or record a radio program ("air check") using the timer, be sure to preset the station beforehand. (Refer to "Presetting or naming radio station" on page 13. ) Power Failures If the power cord is unplugged or there is a power failure, the settings of the current time and once timer are erased and the time display will flash. [. . . ] Files cannot be played if they have any extension other than ". MP3/WMA" or if they have no extension. (with Macintosh computers, MP3/WMA files can be played by adding the extension ". MP3/WMA" after the file name consisting of up to 32 capital or numbers and recording the files on the CD-R/RW. ) · Do not apply stickers, tape, etc. , to either the label side or the signal side of CD-R/RW discs. If adhesive gets on the surface of a disc, the disc may get stuck inside the RCD-N7/RCD-M33 and be impossible to eject. · The RCD-N7/RCD-M33 is not compatible with packet write software. [. . . ]