User manual DENON AVR-989

[. . . ] Be sure to keep this manual for future reference should any questions or problems arise. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" caractéristiques qu'offre cet appareil, lire avec soin ces instructions et bien utiliser l'appareil. Toujours conserver ce mode d'emploi pour s'y référer ultérieurement en cas de question ou de problème. DE SERIE PRIERE DE NOTER LE NUMERO DE SERIE DE L'APPAREIL INSCRIT A L'ARRIERE DU COFFRET DE FAÇON A POUVOIR LE CONSULTER EN CAS DE PROBLEME. " ENGLISH FRANCAIS 2 SAFETY PRECAUTIONS FCC INFORMATION (For US customers) 1. [. . . ] · The TV can be operated when the switch is at DVD/VDP, VCR, TV position. 37 ENGLISH Punch Through · "Punch Through" is a function allowing you to operate the PLAY, STOP, MANUAL SEARCH and AUTO SEARCH buttons on the CD, TAPE, CDR/MD, DVD/VDP or VCR components when in the DBS/CABLE or TV mode. By default, nothing is set. 1 2 Set mode switch 1 to "VIDEO". 3 3 Set mode switch 2 to the component to be registered (DBS/CABLE or TV). 4 1 2 3 Press the OFF (ZONE2) button and the ON (MAIN) button at the same time. · Indicator flash. 4 1 4 7 2 5 8 0 3 6 Input the number of the component you want to set. (See Table 1) Table 1 9 CD TAPE CDR/MD DVD/VDP VCR No setting No. 1 2 3 4 5 0 38 ENGLISH 10 OPERATION Before operating Preparations: Check that all connections are proper. 1 21 3 2 Press the Power switch (button). ON OFF (Main unit) · ¢ ON The power turns on and indicator is light. Set the power switch to this position to turn the power on and off from the included remote control unit. In this position, the power cannot be turned on and off from the remote control unit. 2 Turn on the power. Press the Power ON/STANDBY switch (button). ON / STANDBY (Main unit) (Remote control unit) When pressed, the power turns on and the display lights. The sound is muted for several seconds, after which the unit operates normally. When pressed again, the power turns off, the standby mode is set and the display turns off. 3 3 Select the front speakers. Press the SPEAKER A or B button to turn the speaker on. SPEAKER A B (Main unit) (Remote control unit) · The front speaker A, B setting can be also be changed with the SPEAKER button on the remote control unit. 39 ENGLISH Playing the input source 11 2 5 3 1 3 5 1 Select the input source to be played. Example: CD FUNCTION (Main unit) (Remote control unit) 2 Input mode selection function Different input modes can be selected for the different input sources. If the DIGITAL indicator does not light, check whether the digital input component setup (page 29) and connections are correct and whether the component's power is turned on. NOTE: · The DIGITAL indicator will light when playing CD-ROMs containing data other than audio signals, but no sound will be heard. 41 ENGLISH Playback using the external input (EXT. IN 21 (Main unit) (Remote control unit) Once this is selected, the input signals connected to the FL (front left), FR (front right), C (center), SL (surround left) and SR (surround right) channels of the EXT. IN jacks are output directly to the front (left and right), center and surround (left and right) speaker systems as well as the pre-out jacks without passing through the surround circuitry. In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SUBWOOFER jack. 2 Cancelling the external input mode To cancel the external input (EXT. IN) setting, press the INPUT MODE (AUTO, PCM, DTS) or ANALOG button to switch to the desired input mode. (See page 40. ) INPUT MODE ANALOG 2 1 (Main unit) (Remote control unit) · When the input mode is set to the external input (EXT. IN), the play mode (DIRECT, STEREO, STANDARD (DOLBY/DTS SURROUND), 5CH/7CH STEREO or DSP SIMULATION) cannot be selected. NOTES: · In play modes other than the external input mode, the signals connected to EXT. In addition, signals cannot be output from channels not connected to the input jacks. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode. · If the subwoofer output level seems to high, set the "SW ATT. " surround parameter to "ON". Playing audio sources (CDs and DVDs) The AVR-989/885 is equipped with two 2-channel playback modes exclusively for music. [. . . ] Even with the high quality multi-channel signals, the recording time is the same as with conventional DTS surround sources. What's more, DTS 96/24 is fully compatible with the conventional DTS surround format, so DTS 96/24 signal sources can be played with a sampling frequency of 48 kHz or 44. 1 kHz on conventional DTS or DTS-ES surround decoders ( 2). 1: A DVD player with DTS digital output capabilities (for CD/LD players, a player with digital outputs for conventional DTS CDs/LDs) and a disc recorded in DTS 96/24 are required. 2: The resolution is 24 or 20 bits, depending on the decoder. 71 ENGLISH 18 TROUBLESHOOTING If a problem should arise, first check the following. [. . . ]