User manual DENON AVR-391E3

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. · DECLARATION DE CONFORMITE Nous déclarons sous notre seule responsabilité que l'appareil, auquel se réfère cette déclaration, est conforme aux standards suivants: EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3. D'après les dispositions de la Directive 2006/95/EC et 2004/108/EC. Um dieses Gerät vollständig von der Stromversorgung abzutrennen, ziehen Sie bitte den Stecker aus der Wandsteckdose. Der Netzstecker wird verwendet, um die Stromversorgung zum Gerät völlig zu unterbrechen; er muss für den Benutzer gut und einfach zu erreichen sein. PRECAUTION: · DICHIARAZIONE DI CONFORMITÀ Dichiariamo con piena responsabilità che questo prodotto, al quale la nostra dichiarazione si riferisce, è conforme alle seguenti normative: EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3. [. . . ] · Always set the crossover frequency to "80Hz" When using small . speakers, however, we recommend setting the crossover frequency to a higher frequency. Troubleshooting ENGLISH HDMI Setup 2. Manual Setup Make settings for HDMI video/audio output. s HDMI Video Setup Make settings for HDMI video output. Audio Setup F Menu screen F 2. Manual Setup Getting Started Connections Setup Playback Remote Control Amp Assign Information Troubleshooting Make settings for audio playback. F Menu screen F Color Space 2-2. HDMI Setup 1. HDMI Audio Setup 2. HDMI Video Setup 1. Speaker Setup 2. HDMI Setup 3. Audio Setup 4. Option Setup Make settings for output color space. [Selectable items] YCbCr RGB : Output using YCbCr format. : Output using RGB format. 1. Speaker Setup 2. HDMI Setup 3. Audio Setup 4. Option Setup 2-3. Audio Setup 1. EXT. IN SW Level 2. 2ch Direct/Stereo 3. Dolby Digital Setup 4. Auto Surround Mode 5. Manual EQ a HDMI Audio Setup Make settings for HDMI audio output. When connected to a monitor with a DVI-D connector (HDCP compatible) using an HDMI/DVI converter cable, the signals are output in RGB format, regardless of this setting. a EXT. IN Subwoofer Level Set the subwoofer level for playback. HDMI Audio Out Select HDMI audio output device. RGB Range Make settings for RGB output range. [Selectable items] 0dB +5dB +10dB : Select according to the player in use. [Selectable items] AMP : Use speakers connected to receiver for audio playback. TV : Use speakers of monitor for audio playback. [Selectable items] Normal : Use video range from 16 (black) to 235 (white). to avoid black washout. +15dB : This is the recommended level. Enhanced : Video range from 0 (black) to 255 (white). Use this setting s 2ch Direct/Stereo When "YCbCr" is selected under "Color Space" "RGB Range" will , have no effect. Make speaker settings for 2-channel mode playback. Setting To change the settings, select "Custom" . [Selectable items] Basic : Use the same settings as in "Speaker Setup" . Custom : Make separate settings for 2-channel mode. ENGLISH Front Select front speaker size. d Dolby Digital Setup Set dynamic range for downmix playback of Dolby Digital sources. g Manual EQ Adjust tonal quality for each speaker using graphic equalizer. Getting Started [Selectable items] Large Small : Select front speaker size. [Selectable items] ON OFF : Compression is used. This is the recommended setting. Base Curve Copy Copy the Room EQ´s "Audyssey Flat" correction curve. Connections Subwoofer Select subwoofer use. [Selectable items] Yes No [Selectable items] Yes No : Select subwoofer use. · Set this to "ON" if the sound from the front speakers seems distorted. · When not using the center speaker or surround speakers, the playback sound is down-mixed and output from the front speakers. Setup Subwoofer Mode Select low range signal to be reproduced by subwoofer. "Base Curve Copy" is displayed after the auto setup procedure has been performed. Playback Adjust CH Select speaker adjustment method. [Selectable items] LFE LFE+Main : Select subwoofer signal. Remote Control Amp Assign Information f Auto Surround Mode Make setting for memorizing surround mode setting for each input signal type. [Selectable items] Each CH : Adjust tonal quality for each speaker separately. Names containing up to 5 characters can be input. A1 ~ G8 Select the preset memory number. [Input source] TUNER !@ [ \ ] (space) [Characters that can be input] A~Z a~z 0~9 0 ENGLISH Input Mode Set the input mode for this source. The selectable input modes depend on the input source and "Assign" setting (vpage 31, 32). Operating from the main unit or main remote control unit GOperation on the main unitH n Selecting the "AUTO" "PCM" or "DTS" mode , Press the INPUT MODE button. Names containing up to 5 characters can be input. Getting Started [Characters that can be input] A~Z a~z 0~9 !@ [ \ ] (space) Connections [Input source] TUNER [Selectable items] Analog : Play only signals from analog input. [Input source] CD AUX V. AUX [Selectable items] AUTO PCM DTS Analog EXT. IN : Detect type of digital input signal and decode and play automatically. IN input. Assign Assign input sources to input connectors. Setup CDR DVD/HDP TV/CBL VCR GOperation on the main remote control unitH Press the INPUT button. IN PCM Analog DTS HDMI Select HDMI connector to assign to this source. Playback [Input source] DVD/HDP TV/CBL VCR V. AUX Remote Control Amp Assign Information [Selectable items] HDMI1 : Assign HDMI1 input connector. None : No HDMI input connector assigned. Input source Default setting DVD/HDP HDMI1 TV/CBL HDMI2 VCR None V. AUX None · Only set "PCM" and "DTS" when playing the respective signals. · When a digital signal is properly input, the " " indicator lights on the display. [. . . ] Page 33 Symptom No sound is output from the monitor connected with HDMI connections. Cause · The connections between the AVR-391E3 and monitor are faulty. · The player is connected using the component input connectors, the monitor is connected using the video (yellow) or S-Video output connectors. · The monitor is not compatible with copyright protection (HDCP). [. . . ]