User manual DENON AVR-1913

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. · DECLARATION DE CONFORMITE Nous déclarons sous notre seule responsabilité que l'appareil, auquel se réfère cette déclaration, est conforme aux standards suivants: EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3. D'après les dispositions de la Directive 2006/95/EC et 2004/108/EC. Um dieses Gerät vollständig von der Stromversorgung abzutrennen, ziehen Sie bitte den Stecker aus der Wandsteckdose. Der Netzstecker wird verwendet, um die Stromversorgung zum Gerät völlig zu unterbrechen; er muss für den Benutzer gut und einfach zu erreichen sein. PRECAUTION: · DICHIARAZIONE DI CONFORMITÀ Dichiariamo con piena responsabilità che questo prodotto, al quale la nostra dichiarazione si riferisce, è conforme alle seguenti normative: EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3. [. . . ] Speaker Configuration Subwoofer Mode Setup Distance Crossover Frequency Test Tone Playback Press o p to select the item you want to set, then press ENTER. Press ui to select the item you want to change, then press o p to change the setting. Remote Control To change the setting: Amp Assign Press ENTER or ito confirm the new settings. Press SYSTEM SETUP to move the next category. a ~ h Speaker Configuration Select speaker configuration and size. (bass reproduction capability) uiop ENTER [Display] 1. Sp 2. In 3. Op Q Information b To cancel the system setup mode, press SYSTEM SETUP again. [Rear] 1 ENTER Speaker Setup *System Setup Q Troubleshooting SYSTEM SETUP uiop 2 1 Front 1. Sp 2. In 3. Op Q Large Q Speaker Setup 6 Subwoofer Yes Q 3 About the button names in these explanations < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only: Buttons on the main unit and remote control unit 1 Front Large 5 Front Speaker Select front speaker size. 1. Sp 2. In 3. Op [Selectable items] Large Small ENGLISH Center Speaker Select center speaker use and size. · Select "Large" or "Small" not according to the physical size of the speaker but according to the low frequency reproduction capabilities based on the frequency set at "Crossover Frequency" (vpage 23). · When "Front Speaker" is set to "Small""Subwoofer" is automatically , set to "Yes" . · If "Subwoofer" is set to "No" "Front Speaker" is automatically set to , "Large" . · If "Surround Speaker" is set to "None" "Surround Back Speaker" are , automatically set to "None" . · When using just one surround back speaker, connect it to the left channel (SBL). k ~ A5 Distance Set distance from listening position to speakers. Before making the settings, measure the distance from the listening position to the different speakers. Getting Started Connections Setup Playback Remote Control Amp Assign Information Troubleshooting [Selectable items] Large Small None Surround Speaker Select surround speakers use and size. [Display] 1. Sp 2. In 3. Op Q [Selectable items] Large Small None Speaker Setup Q Surround Back Speaker Select surround back speaker use and size. 8 FL 3. 6m Q [Selectable items] ( Large ( 2spkrs Small 1spkr None ) ) j Subwoofer Mode Setup Select low range signal to be reproduced by subwoofer. 15 SW 3. 6m Subwoofer Select subwoofer use. [Display] Yes No 1. Sp 2. In 3. Op Q Distance measurement Select the speaker you want to set, then set the distance. Set the value closest to the measured distance. [Selectable items] [Variable range] Q Speaker Setup Large : Select this when using large speakers with ample low frequency reproduction capabilities. 0. 0m ~ 18. 0m : Settable in units of 0. 1 meters. NOTE Set the distance between the listening position and the various speakers to no more than 6. 0 meters. 7 SW Mode Norm Small : Select this when using small speakers without ample low frequency reproduction capabilities. : Disable conversion. +15dB : This is the recommended level. [Display] 1. Sp 2. In 3. Op E Remote Control A5 Audio Delay Compensate for mismatched timing between video and audio. A7 Auto Preset Memory Use the auto preset function to program radio stations. Option Setup E Amp Assign 1 Amp 7. 1ch To suit your preference, a surround back channel's power amplifier can be assigned to the front channel ("Front A" or "Front B") for biamp playback. [Display] 1. Sp 2. In 3. Op W [Display] 1. Sp 2. In 3. Op W Information Input Setup W Input Setup W [Selectable items] 7. 1ch FrontA Bi-Amp FrontB Bi-Amp 15A. Delay 0ms Delay audio. This sets the delay time for audio signals. 17 Preset <Start Press the o button to start. · "Completed" appears once searching is completed. Troubleshooting For details, see "Amp Assign" (vpage 46). [Variable range] 0 ms ~ 200 ms With a movie source, for example, adjust so that the movement of the actors' lips is synchronized with the sound. If an FM station cannot be preset automatically, select the desired station by tuning it in manually, then preset it manually. This cannot be adjusted when playing in the EXT. IN, DIRECT or STEREO mode (with "Front Speaker" set to "Large" "Tone Defeat" to , "ON" and "Room EQ" to "OFF" . ) Operations (vpage 21) ENGLISH s ~ f Volume Control Set the main zone volume setting. Mute Level This sets the amount of attenuation of the volume when the mute mode is set in the main zone. Setting To change the settings, select "ON" . Getting Started Connections Setup Playback Remote Control Amp Assign Information Troubleshooting [Display] 1. Sp 2. In 3. Op E [Selectable items] Full : The sound is cut off entirely. [Selectable items] OFF ON z : To change the settings, select "ON" . : Make separate settings for 2-channel mode. Option Setup E ­40dB : The sound is attenuated by 40 dB. ­20dB : The sound is attenuated by 20 dB. z: Use the same settings as in "Speaker Setup" . 2 Limit 3 P. On 4 Mute OFF E Front Select front speaker size. LAST E g ~ A1 2ch Direct/Stereo Custom Make speaker settings for 2-channel mode playback. [Selectable items] Large Small : Select front speaker size. FULL [Display] Volume Limit Make a setting for maximum volume. Subwoofer Select subwoofer use. E 1. Sp 2. In 3. Op Option Setup E [Selectable items] OFF : Do not set a maximum volume. [Selectable items] Yes No : Select subwoofer use. 5 2ch Cstm 5 2ch Cstm 6 2ch F 7 2ch SW OFF E ­20dB : Set the maximum volume to ­20 dB. 0dB : Set the maximum volume to 0 dB. ON E Subwoofer Mode Select low range signal to be reproduced by subwoofer. Large E [Selectable items] LFE (Normal) LFE+Main : Select subwoofer signal. Power On Level This sets the volume set when the main zone's power is turned on. Yes E [Selectable items] Last ­­­ : Use the memorized setting from the last session. in units of 1 dB. 8 2ch LFE 9 2ch FL 10 2ch FR 11 2ch Freq Norm E Distance FL Set distance from listening position to front left speaker. 3. 6m E 3. 6m E [Variable range] 0. 0m ~ 18. 0m ­80dB ~ +18dB : Set the volume level when the power is turned on 80 Operations (vpage 21) ENGLISH Distance FR Set distance from listening position to front right speaker. A3 Room EQ Setup Select room EQ setting method. A5 Remote ID Setup Set remote control ID. Getting Started [Variable range] 0. 0m ~ 18. 0m [Display] 1. Sp 2. In 3. Op E [Display] 1. Sp 2. In 3. Op E Crossover Select crossover frequency from which subwoofer handles low range signal. Connections Option Setup E Option Setup E [Selectable items] 40Hz 200Hz 60Hz 80Hz 90Hz 100Hz 110Hz 120Hz 150Hz 250Hz : Select crossover frequency. [Selectable items] All 13 EQ All 15 Remote ID 1 Setup [Selectable items] NOTE 1 2 3 4 : Apply settings to all surround modes. When using the AVR-1913 with only the included remote control unit (RC-1076), there is no need to make settings. When using a separately sold remote control unit (RC-7000CI, etc. ), this function can be used. [. . . ] Page 28 Symptom No sound is output from the monitor connected with HDMI connections. Cause · The connections between the AVR-1913 and monitor are faulty. · The player is connected using the component input connectors, the monitor is connected using the video (yellow) or S-Video output connectors. · Input source does not match recorder's video connection connector (video or S-Video). [. . . ]