User manual DAEWOO WM-501

[. . . ] - Very low temperature setting considerably increase power consumption. - Avoid continuous direct air flow on you or a sick person while sleeping. - Damage to the cord and may cause shock hazard. 1 TABLE OF CONTENTS 1. GENERAL SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. [. . . ] Measure width between window frame to be sure instant mount will fit in the window. Instant mount models are designed for windows 22 in (559mm) to 36 in (915mm) wide. (The outside edge of window bracket should be 5. 9 in (150mm) from center line) 6. Place the carpenter's level on the sill and the outdoor end of Sill Bracket. Turn Screw (Type A) until the level's bubble is centered. Screw (Type B) SILL BRACKET OUTER WINDOW SILL CENTER LINE INNER WINDOW SILL SILL BRACKET Screw (Type A) OUTER WINDOW SILL WALL 140 70 90 UNIT 150mm (5. 9in) INNER WINDOW SILL SASH BRACKET 38 145 (130) 55 (135 MAX) SILL BRACKET 5 · Step 3 - Placing Unit in Window CAUTION 1. To avoid injury or accident, it is strongly recommended that you have additional help when lifting the unit. Personal injury or property damage may result if unit falls from window. 1. (Screws are ready provided in the each side as part of the Air-Conditioner for this purpose. So, at first, please remove this screws, and re-attach Sash Bracket to the same portion with Screws (Type C) of components for installation. ) 2. Fasten window shutter in the window kit frame with Screws (Type D) in the left side and right side of the unit. (1) Remove the attached screw Cabinet (2) Insert Sash Bracket between Cabinet and Base Pan (3) Attach Sash Bracket with the screw of (1) and the screw of components of installation Screw (Type C) WINDOW KIT FRAME PLATE WINDOW TOP (upper guides) WINDOW SHUTTER (bottom guides) Screw (Type C) SASH BRACKET Screw (Type D) · Step 4 - Install Sash Bracket CAUTION Do not drill into window frame until window has been inspected to make sure drilling or screw will not damage any locking or lifting mechanism located the frame. Fasten Sash Bracket be attached in the unit's side with Screw (type C) on the window sill. (It is the same to install Sash Bracket left side and right side. ) 2. Fasten Sash Bracket with Screw (Type C) to top of indoor window sash or directly into side of window sash or directly into side of window frame. If you have a hard wood or metal window frame, a 1/8 inch pilot hole may be needed in order to drive the screw. 6 SASH BRACKET WINDOW FRAME WINDOW SASH Screw (Type C) · Step 5 - Secure Window Shutter CAUTION Do not drill into window sash until window has been inspected to make sure drilling or screw will not damage any locking or lifting mechanism located in the frame. To provide a proper seal, pull each expandable side Window Shutter out and up until it is tight against the window frame. Using the hole in the top and bottom of each Window Kit Frame as a guide, secure Window Kit Frame in window sash and on the window sill. WINDOW KIT FRAME Screw (Type C) WINDOW SASH WINDOW SHUTTER WINDOW FRAME Screw (Type C) INNER WINDOW SILL · Step 6 - Recheck Installation To be sure you have correctly installed your Room Air Conditioner, review the steps and make sure all of the parts are securely fastened in the window as the instructions show. Read through the Use & Care manual to become familiar with the operation of your room air conditioner. CAUTION Do not lift window sash without holding the unit. Failure to do so many result in personal injury and/or property damage. 7 NAMES OF MAJOR COMPONENTS · WM-501 1 2 3 8 5 9 6 0 q 4 7 w NO 1 2 3 4 5 6 PART NAME CABINET BLADE VERTICAL COOL AIR DISCHARGE GRILL FRONT KNOB SELECTOR KNOB THERMOSTAT NO 7 8 9 10 11 12 PART NAME AIR INTAKE AIR FILTER CONTROL PANEL PLATE WINDOW TOP FRAME WINDOW KIT SHUTTER WINDOW 8 OPERATING INSTRUCTIONS NOTE · FOR MOST ECONOMICAL USE 1. Do not leave doors and windows open. · FAN & COOLING CONTROL The Fan Control Selector Switch has five positions. Choose one of the speed settings by rotating the fan control Selector Switch to the appropriate position. CAUTION When the air conditioner has been performing its cooling operation and is turned "OFF" or set to the `FAN" position, wait at least 3 minutes before resetting to the cooling operation. SELECTOR OFF OFF LOW FAN LOW COOL Select this setting for stop all operation of air conditioner Select this setting for maximum air circulation without cooling. After cleaning or performing maintenance, reconnect power. · AIR FILTER Clean the air filter, which removes dust inside the room. Replace it. SELECTOR OFF LOW FAN LOW COOL HIGH FAN HIGH COOL THERMOSTAT COOLER NOTE A dirty Air Filter reduces air flow and the cooling capacity. [. . . ] To establish and receive warranty service at our store, dealer or our authorized service center, a sales receipt or bill of sales is required for proof of purchase. This warranty does not extend to any of our electronic products which have been subjected to misuse, neglect, accident, incorrect wiring not our own, improper installation, unauthorized modification, or to use in violation of instructions furnished by us, nor units which have been repaired or altered outside of our factory, nor to cases where the serial number thereof has been removed, defaced, or changed. This warranty is in lieu of all warranties expressed or implied and no representative or person is authorized to assume for us any other liability in connection with the sales of our electronic products. Initial defective is described as when the dealer opens the unit and finds that it is inoperative or an individual customer opening a new unit and finding that it is initially defective. [. . . ]