User manual DAEWOO ST737

[. . . ] WORTH knowing Please keep the video's guarantee sheet and receipt for your video in a safe place. Precautions x x x x x x AUTO SET OP EJECT CH. x x Read this booklet carefully. Make sure the rating of your household electricity supply matches that shown on the back of the video recorder. Read this page and the chapter and the "Setting up your video" to help you set up and adjust your video recorder. Do not put the video recorder in a hot or humid place (to avoid the risk of fire and electric shock). [. . . ] Confirm the setting with OK. · EJECT SP/LP PAL/SEC INDEX PR MENU 16:9 Set -Auto : This video automatically detects the program format (16:9 or 4:3) and records or plays this program in the same format. -OFF : The video will play or record all broadcasts in 4:3 format only. PR A. SEL 3 For the above formats to work your TV must be able to automatically detect a 16:9 broadcast. In the case of turning 16:9 format off, your TV may override this decision and display the picture in 16:9 format. 15 CM Skip 30 If you press [CM Skip] button on the remote control during playback mode, tape advances for 30 seconds segment. Auto Repeat If you press the PLAY button for 5secs during playback mode, REP should appear on your display, the video goes into Auto repeat mode. To release this mode, press any mode operation button such as PLAY, FF, REW or STOP. Child lock You can only set the child lock with your remote control. Press the button for about 5 seconds. No buttons of front panel can be operated now and LOCK INDICATOR ("SAFE") will be displayed momentarily on LED display. To release child lock, press any button of the remote control. 16 OSD(On Screen Display) ON & OFF This VCR is set to "OSD (On Screen Display) ON" mode at the factory, but you can change it to OFF mode. When a function is changed at the front display or remote control the change will be displayed on the screen. 1 MAIN MENU TIMER PROGRAM PR PRESET VCR SETUP TAPE CONTROL PR+/-:SELECT OK:CONFIRM MENU:END Press MENU. Choose "VCR SETUP" And press OK. 2 VCR SETUP CLOCK SET LANGUAGE SET RF OUTPUT SET 16:9 SET OSD ON/OFF PR+/-:SELECT OK:CONFIRM MENU:END Choose "OSD ON/OFF". 3 OSD ON/OFF ON OFF PR+/-:SELECT OK:CONFIRM If you want OSD OFF mode, press PR- and press OK. OSD characters will not be displayed in the normal picture at the start of each mode change. MENU:END Setting time and date CLOCK SET 1 TIME - - : - DATE - -/- -/- - - 0-9:SETUP (HOUR) / :CORRECT OK:CONFIRM MENU:END If the `CLOCK SET' display is not already on the screen press MENU. Once the `CLOCK SET' display is on the screen, move to the position you want to change by pressing or . Use the number buttons 0 to 9 on the remote control to enter the correct time and date. Press OK to confirm the settings, and press MENU to end. CLOCK SET 2 TIME 11:41 DATE 12/05/2003(MON) 0-9:SETUP (HOUR) / :CORRECT OK:CONFIRM MENU:END 17 Recording cassettes x x If you want to use the video's timer to record a programme, the clock, date and stations must be set correctly. Load a cassette with its safety tab in place (see page 24) and with enough free tape for the recording. Simple recording Load a cassette with its safety tab in place (see page 24). STOP PROG SP PR01 ARD STEREO ON 1 4 2 5 3 6 TV/VCR AV A Press PR+ or PR- to choose the station you want to record. Press SP/LP if you wish to double the length of the cassette's recording time. For example, on an E-240 cassette you can record for up to four hours when SP is displayed, or up to eight hours when LP is displayed. 7 8 9 30 0 VCR EJECT Press to start your recording. SP/LP PAL/SEC INDEX PR MENU Press if you want to stop the recording for a short while. VCR PR A. SEL Press VCR to continue recording. to stop your recording. Press One-touch recording-OTR These buttons are used on the following two pages. VCR Press PR+ or PR- to choose the station you want to record. Every time you press , the recording time will increase by 30 minutes. It is possible to record for up to 10 hours if there is enough room on the cassette. · To cancel OTR press and hold the STOP button for about five seconds until the video stops recording. · If you want to record from other equipment that is connected to your video, see pages 3, 4 and 9. 18 Timer recording using ShowView ShowView is an automatic system which makes it easier to set the timer. 1 SHOWVIEW 83077---0-9:SHOWVIEW NUMBER :CORRECT OK:CONFIRM MENU:END Press PROG. (If ShowView mode does not appear on the screen, it is not available on your video. From your current TV guide, type in the number next to the programme you want to record using the number buttons 0-9. Press PR+ or PR- to select how often you want to make the recording, for example, once, weekly and so on. If you wish to change any details: Move to the details you want to change using the / buttons. Change the setting using the PR+ or PR- or number buttons 0-9. 2 HOW OFTEN DO YOU WANT TO RECORD THIS PROGRAM? ONCE WEEKLY(ONCE A WEEK) DAILY(MON-FRI) DAILY(MON-SAT) DAILY(MON-SUN) PR+/-:SELECT OK:CONFIRM MENU:END 3 PR 03 START TIME 21:20 END TIME 22:20 START DATE 14/05(WED) TAPE SPEED SP VPS/PDC ON PR+/-:SELECT (AV1/AV2) 0-9 : SETUP (PR) / :CORRECT OK:CONFIRM MENU:END TIMER PROGRAM (ONCE) If all the settings are correct, press OK. [. . . ] In this case, please turn to page 5 and carry out step 2 until you see the manual tuning screen. A blue screen is displayed when you switch the video on If a blue screen appears when you switch the video on, the AV button has been pressed. Press AV on the remote control until P-_ _ appears on the display of the video, or until a TV picture is displayed. The timer light stays on the display, even though the recording has finished If the timer light stays on even though the recording has finished, this is because VPS/PDC takes into account a delay in recording for up to 24 hours. The TV/VCR button on the video remote control will not work This button will only work if the TV has the appropriate internal switch and a scart lead is connecting the TV and video. The television will not change channel when the video is turned on If the television will not change channel while the video is on, check whether a scart lead has been connected. (See page 2 option 2) If a scart lead has been connected, you need to press the TV/VCR button on the video remote control. When the small VCR symbol appears on the display, you can only change channel by using the video remote control. [. . . ]