User manual DAEWOO DWF-7094

[. . . ] Please read it carefully. 2 PARTS AND FEATURES The parts and features of your washer are illustrated on this page. Become familiar with all parts and features before using your washer. NOTE · The drawings in this book may vary from your washer model. They are designed to show the different features of all models covered by this book, Your model may not include all features. · HOT WATER TAP · BLEACH INLET After using the washer, close the water tap, In case of the single valve model, there is no hot water valve. · COLD WATER TAP After using the washer, close the water tap · CASE DETERGENT AND SOFTENER · LINT FILTER(2EA) · PULSATOR · CONTROL PANEL · GROUND WIRE(OPTION) In case of 3-wire power cord ground wire will not be provided · POWER CORD · HOSE DRAIN · ADJUSTABLE LEG ACCESSORIES DRYTEN (OPTION) COVER UNDER (OPTION) WATER TAP ADAPTER INLET HOSE DRYTEN U P HOSE DRAIN (FOR PUMP) HOSE DRAIN CLAMP HOSE DRAIN (FOR NON-PUMP) CONNECTOR INLET(OPTION) 2 3 WASHER SAFETY Save these instructions Your safety is important to us. [. . . ] · Turn down cuffs and turn synthetic knits out to avoid pilling. (see "Removing stains" on page14) Sorting · Separate heavily soiled items from, lightly soiled ones, even if they would normally be washed together. · Separate dark colors from light colors, color Loading · Drop items into washer loosely. Items should move easily through wash water for best cleaning and wrinkle-free results. Overloading and selecting a setting too small for the wash load can: - cause poor cleaning - increase wrinkling - create excessive lint - wear out items faster (because of pilling) · Mix large and small items in each load. · Use a large load size setting to reduce wrinkling with permanent press clothes and some synthetic knits. These items should have more room to move in the water than heavy items (towels, jeans) 7 8 THE FUNCTIONS OF THE CONTROL PANEL AUTOMATIC WASHING M ACH INE LOW E. LOW MEDIUM HIGH a WATER LEVEL WATER LEVEL ECO. WASH PROCESS RINSE POWER REMAIN WOOL COURSE BLANKET a PROCESS ADD MIN. a FU LL COURSE FUZZY SPIN WASH TEMP. COLD HOT WASH TEMP. START HOLD POWER · Press this button to turn the power "ON" or "OFF". · As the button is pressed, water temperature will be repeated. COLD ¨ COLD + HOT ¨ HOT · In case of the single valve model, there is no wash temperature selector function. · It can be used to adjust amount of water according to the size of the load to be washed. · As the button is pressed, water level is selected by E. LOW ¨ LOW ¨ MEDIUM ¨ HIGH · It is the button for the partial process or the combination of each process (wash, rince, spin) (See page 10) · It can be used to select the full-automatic course. · As the button is pressed, course will be selected by following order: FUZZY ¨ BLANKET ¨ WOOL ¨ ECONOMY. Only Wash Press the Process button, six times. q WASH q RINSE q ADD q SPIN r WASH r RINSE r ADD q SPIN r WASH q RINSE r ADD q SPIN r WASH q RINSE q ADD q SPIN r WASH q RINSE r ADD r SPIN q WASH r RINSE r ADD r SPIN 3 Selecting 4 Pressing the Water level & Start/Hold Water Temp. r LOW r E. LOW PROCESS POWER End of Washing WATER LEVEL START HOLD It is Informed by buzzer IN CASE OF ONLY DRAIN 1 Press the power button. (It same with spin only) 3 Press Start/Hold with opening DOOR. START HOLD POWER PROCESS · After finishing Drain, the Buzzer is ringing and PCB is displaying "LE" message. · After Drain, please turn off the power. 10 11 GENERAL PROCEDURE FOR OPERATION 1. Add measured detergent to the washer, (Follow manufacturer s directions for safe use) 2. OPTIONAL STEP If desired, add measured liquid chlorine bleach to the bleach inlet, use only liquid chlorine in the bleach inlet * Follow manufacturer's direction for safe use. NOTE · Do not let bleach splash, drip, or run down into washer basket. · Do not use this dispenser to add powdered chlorine or color safe bleach to your wash load. The full automatic cycle has four settings; FUZZY, BLANKET, ECONOMY, WOOL. (See page 9) 6. [. . . ] · The sound "sha" heard in stopping the tub is the sound that comes from the autobalancer of the tub. · The sound "wung" heard during wash or spin is the operating sound made by the air bubble generator. NOTE Please check the point before calling for a service. If the supply cord is damaged, it must only be replaced by a repair shop appointed by manufacturer, because special purpose tools are required. 15 SPECIFICATIONS NO. 1 2 ITEM POWER SOURCE 50Hz POWER CONSUMPTION 400W MACHINE NON-PUMP 3 WEIGHT 4 5 6 PUMP DIMENSION (WXHXD) WASHING COURSE (FUZZY, MEMORY, BLANKET, SUIT, HEAVY, ECONOMY) WATER CONSUMPTION NORMAL 190L HIGH(68L), MEDIUM(57L) 7 WATER LEVEL SELECTOR LOW(46L), SMALL(35L) E. SMALL(28L) 8 OPERATING WATER PRESSURE 2 DWF-7094 DWF-8094 AVAILABLE IN ALL LOCAL AC VOLTAGE AND CYCLE 60Hz 50Hz 400W 60Hz 430W 50Hz 480W DWF-1094 [. . . ]