User manual DAEWOO DWF-5520

[. . . ] Washing Program 4 Programs Water Level High (55 Liters), Medium (45 Liters), Low (31 Liters) Direction of Inlet Valve Backward Upward Backward Upward Operating Water Pressure 0. 3Kgf/cm2~8Kgf/cm2 (2. 94N/cm2~78. 4N/cm2) Pulsator Provided with 6 Spouting Holes for Powerful Upward Water Stream 1. Signal Buzzer for the Operation of Control Button Coin Filter Only in Pump Model identified with `P' added to Model No. (e. g. , DWF-5510NP) The above specifications and features are subject to change without prior notice. 2 PARTS DESCRIPTIONS DETERGENT CASE (Symbol ) WATER CONNECTOR (Blue Color: Cold, Pink Color: Hot) DOOR DRAIN HOSE LINT FILTER FABRIC SOFTNER INLET (Symbol, See page 10) LIQUID BLEACH INLET (Symbol, See page 10) CONTROL PANEL (88 display and some buttons may be excluded) WASH TUB PLUG PULSATOR BASE (Height is optional) GROUND WIRE (This will not be provided in case of 3-wire power cord) ADJUSTABLE LEG (Optional) N The drawings in this book may vary from your washer model. [. . . ] Items should move easily through wash water for best cleaning and wrinkle-free results. Overloading and selecting a setting too small for the wash load can: - cause poor cleaning - increase wrinkling - create excessive lint - wear out items faster (because of pilling) · Mix large and small items in each load. · Use a large load size setting to reduce wrinkling with permanent press clothes and some synthetic knits. These items should have more room to move in the water than heavy items (towels, jeans) 8 DESCRIPTIONS OF CONTROL PANEL DWF-5510/5511/6010/6011 HIGH POWER MID LOW °° RES. FUZZY LIGHT HEAVY WOOL/SUIT ADD WASH RINSE SPIN HOT COLD START / HOLD WA T LEV ER EL RES. COURSE PROCE SS P TEM DWF-5520/5521/6020/6021 HIGH POWER MID LOW °° RES. FUZZY LIGHT HEAVY WOOL/SUIT ADD WASH RINSE SPIN HOT COLD START / HOLD WA T LEV ER EL RES. COURSE PROCE SS P TEM POWER Power Switch Press this button to turn the power ON or OFF. Water Level Selector This button is used to select the water level you want. Reservation Button If you want to reserve the finishing time of washing, use this button. As this button is pressed, digit in display increases by 1 hour at one press. If current time is 8:00 am and you expect washing will be completed around 5:00 pm, press this nine times in order to display `9'. Course Selector This button is used to select the washing course according to the type of wash loads. Program Button With this button, you can create new programs by combinations of process. Temperature Selector (Optional) If your washer is connected to two water taps for cold water and hot water, you can select them. Start/Hold With this button, you can make your washer proceed your program, or stop temporarily. 9 WATER LEVEL RES. COURSE PROCESS TEMP START / HOLD ; ; GENERAL PROCEDURES FOR OPERATION 1. (1. 2kg's limitation for 1 time-wash) · Do not put leather clothes, or chamois clothes into the washing tub for washing. · The water temperature is fixed to "COLD" · The water level "LOW" is not select. @ Press the course selection button for "WOOL" FUZZY HIGH LIGHT HEAVY MID LOW # Select the water level proper to the wash load. $ Press the Start/Hold button, and close the lid. POWER WOOL START / HOLD COURSE WATER LEVER Suit Course (Option) · This selection is effective for High-quality sweater, wool etc. . (1kg's limitation for 1 time-wash) · Put in the wash market with "Dry Cleaning". @ Press the course selection button for "SUIT". FUZZY LIGHT HEAVY START / HOLD SUIT COURSE # Select the water level proper to the wash load. HIGH MID LOW $ Press the Start/Hold button, and close the lid. % Put the clothes into the tub after the buzzer sounds. ^ Press the Start/Hold button, and close the lid. START / HOLD START / HOLD WATER LEVER 12 GUIDES FOR OTHER USEFUL PROGRAMS For the partial process or the combinations, or for adding time of each process. step 1. Press program button until the indicaing lamps make the combinations you want. If only spin lamp is turned on, that means you will operate your washer for spin only. If rinse and spin lamp are turned on, that means you will operate your washer for rinse and spin. If add lamp is turned on with other process lamps, that means the time of the corresponding process will increase by 1~2 minutes, that is, if add is on with wash, rinse and spin, the time of each process will increase by 1~2 minutes. [. . . ] Rub in an enzyme prewash and wash as normal Lay the affected area face down on an absorbent cloth and work from the back. Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid and wash normally. Dampen a cloth with hydrogen peroxide, lay it over the affected area and press with a fairly hot iron. 16 TROUBLE SHOOTING GUIDES Most problems are easily solved if you understand the cause. Check the following list for problem befor calling for service. Before calling for service, check these PROBLEM · The washer will not operate at all. [. . . ]