User manual DAEWOO DWC-064R

[. . . ] PRECAUTIONS FOR PROPER USE OF AIR CONDITIONER Please observe the following instructions. - Do not use Main Power Switch or Auxiliary Power Switch to operate unit. Avoid exposing your body directly to a continuous cool air - flow for long periods. When the air inlet grill and cabinet are dirty, wipe with luke - warm water (below 104°F or 40°C) 5. [. . . ] Failure to do so many result in personal injury and/or property damage. · Step 7 - Install Unit and assemble Front Grille 1. (High¡Low¡High) TEMP MODE · Everytime you push this button, it is selected as follow. (COOLING¡TURBO¡FAN ¡COOLING) TEMPERATURE · It is the button to set the room in the desired room temp. can be set within a range from 16°C (60°F) to 32°C (90°F) by 1°C (1°F) ENERGY SAVE · Whenever you push this button, the cumulative power consumption is decreased. POWER ON/OFF · To turn the unit ON, push this button. To turn the unit OFF, push this button, again. 11 FUNCTION POWER ON or POWER OPERATION 1. `ROOM TEMP' lamp lights. FAN TURBO COOLING TIMER Push POWER button ROOM TEMP DESIRED TEMP ENERGY SAVE 1. Operating modes are changed as follows by pushing "MODE" button. The desired room temperature is changed within a range from 16°C (60°F) to 32°C (90°F) by 1°C (°F) COOLING MODE 1. `ROOM TEMP' lamp lights. FAN TURBO COOLING TIMER ROOM TEMP DESIRED TEMP ENERGY SAVE 1. It display desired room temperature when `TEMP' button is pushed. `DESIRED TEMP' lamp lights. FAN TEMP TURBO or TEMP ROOM TEMP DESIRED TEMP COOLING TIMER ENERGY SAVE Push the `TEMPvw' button. 3. After a few seconds, display is changed to current room temperature and `ROOM TEMP' lamp lights. FAN SPEED is changed as follows by pushing "FAN SPEED" button. It displays as follows. Change `FAN SPEED' FAN SPEED FAN SPEED or HIGH LOW Push the `FAN SPEED' button. 2. After a few seconds, display is changed to current room temperature. 12 FUNCTION FAN MODE MODE MODE OPERATION 1. `ROOM TEMP' lamp lights. FAN TURBO or Push the `MODE' button until `FAN' lamp lights. ROOM TEMP DESIRED TEMP COOLING TIMER ENERGY SAVE ON/OFF ENERGY SAVE ENERGY SAVE ENERGY SAVE or 1. Desired temperature is changed as follows by pushing `ENERGY SAVE' button. +1°C +1°C -2°C 1. `ROOM TEMP' lamp lights. FAN Push the `ENERGY SAVE' button. 1hr `ENERGY SAVE' ON hr `ENERGY SAVE' OFF ROOM TEMP DESIRED TEMP TURBO COOLING TIMER 2. When the `ENERGY SAVE' button is pushed, the fan speed goes to `Low' 3. When the `ENERGY SAVE' function is canceled by pushing `ENERGY SAVE' button once again, the desired temperature is return to the former desired temperature. Fan speed is set to `HIGH' and desired temperature to 18°C (64°F). or 1. `ROOM TEMP' lamp lights. FAN Push the `MODE' button until `TURBO' lamp lights. ROOM TEMP DESIRED TEMP TURBO COOLING TIMER ENERGY SAVE OFF TIMER TIMER/ CANCEL 1. [. . . ] If a two-prong wall receptacle is encountered, the customer is required to contact a qualified electrician and have the two-prong wall receptacle replaced with a properly grounded three-prong wall receptacle in accordance with the National Electrical Code. WARNING : To avoid death, personal injury or properly damage due to electrical shock, this unit must be grounded. Do not under any circumstances cut or remove the round grounding prong from the plug. Do not use a two prong adapter. · USE OF EXTENSION CORD Because of potential safety hazards under certain condition, we strongly recommend against the use of an extension cord. However, if you still elect to use an extension cord, it is absolutely necessary that it will be a UL listed 3-wire grounding type appliance extension cord rated has a 3-blade grounding plug and a 3-slot receptacle that will plug into the appliance. [. . . ]