User manual DAEWOO DWC-051C

[. . . ] - Very low temperature setting considerably increase power consumption. - Avoid continuous direct air flow on you or a sick person while sleeping. - Damage to the cord and may cause shock hazard. 1 TABLE OF CONTENTS 1. GENERAL SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. [. . . ] Instant mount models are designed for Windows 24 inch (610mm) to 36 inch (914mm) wide. Attach Sill bracket to window sill using two Screws (Type B) by each bracket. The outside edge of window bracket should be 9. 4 inch (240mm) from center line. Adjust Screw (Type A) so that Sill Bracket have a slight tilt by using carpenter's level meter. Screw Type B SASH SILL BRACKET SI LL 480mm 600mm 240mm 300mm Screw Type A 720~915mm 610~914mm · Step 3 - Preparation of Chassis 1. ­ Push the right lower side of chassis to the left, with pushing left side of Front Grille to the right until the snap-fit is released. Push Push 2) Release left-lower snap-fit. ­ Push the left-lower side of chassis to the right, with pushing right side of Front Grille to the right until the snap-fit is released. Push Push 3) Pull lower side of the Front Grille until it is separated from the chassis. (when knobe remain, pull Front Grille until knobs are released from control) 4) Push base side of the Front Grille to upper side until it is separated from the chassis. 5. After front grille is removed, remove two screws located in both side of chassis and pull out the unit from chassis. 6 · Step 4 - Placing Chassis 1. Insert narrow side of `Frame Guide Lower' to rectangle holes Guide Lower located in bottom of chassis, and fasten it with Screw (Type D). Place the chassis on the window sill and align it with Sill Bracket and sill with Lower Frame Guide and locate window sash to Top Frame Guide. (check the end of chassis for about 1/2 inches (12mm) distance below the level. ) 5. Fasten Sash Bracket with Screw (Type C) to top of indoor window sash or directly into side of window sash or directly into side of window frame. If you have a hard Screw (Type D) wood or metal window frame, a 1/8 inch pilot hole may be needed in order to drive the screws. Attach the Window Seal A to window (see the picture shown in step 8, page 8) FRAME Screw Screw (Type D, both side) E, side) Frame Guide Top Window Seal B SASH BRACKET Screw (Type C) Screw (Type C) · Step 5 - Secure Window Shutter CAUTION Do not drill into window sash until window has been inspected to make sure drilling or screw will not damage any locking or lifting mechanism located in the frame. To provide a proper seal, pull each expandable side Window Shutter out and up until it is tight against the window frame. Using the hole in the top and bottom of each Window Kit Frame as a guide, secure Window Kit Frame in window sash and on the window sill. WINDOW KIT FRAME Screw (Type C) WINDOW SASH WINDOW SHUTTER WINDOW FRAME Screw (Type C) INNER WINDOW SILL 7 · Step 6 - Recheck Installation To be sure you have correctly installed your Room Air Conditioner, review the steps and make sure all of the parts are securely fastened in the window as the instructions show. Read through the Use & Care manual to become familiar with the operation of your room air conditioner. Failure to do so many result in personal injury and/or property damage. · Step 7 - Install Unit and assemble Front Grille 1. If the room temperature is not satisfactory after a reasonable period of time, adjust the temperature control to a lower or higher setting. · The Thermostat automatically starts and stops cooling operation in order to keep the room temperature at a proper level, and this results in efficient use of power and economical cooling. · Turn counter-clockwise for a warmer room temperature. THERMOSTAT 10 GENERAL INFORMATION · CHANGING AIR FLOW DIRECTION Air flow deflectors divert air from center flow to left or right and up or down. Adjust deflectors for desired air flow pattern. · AIR FLOW AROUND UNIT Check in door grill and outdoor louvers for air flow obstructions. The outdoor coil should be checked and periodically cleaned for debris that may collect and block unit air flow. [. . . ] To establish and receive warranty service at our store, dealer or our authorized service center, a sales receipt or bill of sales is required for proof of purchase. This warranty does not extend to any of our electronic products which have been subjected to misuse, neglect, accident, incorrect wiring not our own, improper installation, unauthorized modification, or to use in violation of instructions furnished by us, nor units which have been repaired or altered outside of our factory, nor to cases where the serial number thereof has been removed, defaced, or changed. This warranty is in lieu of all warranties expressed or implied and no representative or person is authorized to assume for us any other liability in connection with the sales of our electronic products. Initial defective is described as when the dealer opens the unit and finds that it is inoperative or an individual customer opening a new unit and finding that it is initially defective. [. . . ]