User manual DAEWOO DWA-122R

[. . . ] PRECAUTIONS FOR PROPER USE OF AIR CONDITIONER Please observe the following instructions. - Do not use Main Power Switch or Auxiliary Power Switch to operate unit. Avoid exposing your body directly to a continuous cool air - flow for long periods. When the air inlet grill and cabinet are dirty, wipe with luke - warm water (below 104°F or 40°C) 5. [. . . ] (High¡Mid¡Low¡High) POWER ON/OFF SWITCH · To turn the unit ON, push this button. To turn the unit OFF, push this button again. AUTO SWING · Everytime you push this button, the auto swing mode is toggled. MODE SELECT · Everytime you push this button, It is selected as follow. (COOLING¡TURBO¡FAN¡COOLING) 10 · REMOTE CONTROL REMOTE SIGNAL TRANSMITTER TIMER/CANCEL · Everytime you push this button, timer is set as follow. (1Hr¡2Hr¡3Hr¡4Hr¡5Hr¡6Hr ¡8Hr¡10Hr¡12Hr¡16Hr¡20Hr ¡24Hr¡CANCEL). After the unit is timed, if this button is pushed, timer is canceled. TIMER/ CANCEL SLEEP SLEEP · SLEEP mode is selected as follow. (L1¡L2¡Cancel) FAN SPEED AUTO SWING MODE FAN SPEED · Everytime you push this button, it is selected as follow. (High¡Mid¡Low¡High) TEMP MODE · Everytime you push this button, it is selected as follow. (COOLING¡TURBO¡FAN ¡COOLING) TEMPERATURE · It is the button to set the room in the desired room temp. can be set within a range from 16°C (60°F) to 32°C (90°F) by 1°C (1°F) AUTO SWING · Everytime you push this button, the auto swing mode is toggled. POWER ON/OFF · To turn the unit ON, push this button. To turn the unit OFF, push this button, again. 11 FUNCTION POWER ON POWER OPERATION 1. `ROOM TEMP' lamp lights. or Push POWER button FAN TURBO COOLING ROOM TEMP DESIRED TEMP TIMER 1. Operating modes are changed as follows by pushing "MODE" button. The desired room temperature is changed within a range from 16°C (60°F) to 32°C (90°F) by 1°C (°F) COOLING MODE 1. `ROOM TEMP' lamp lights. FAN TURBO COOLING ROOM TEMP DESIRED TEMP TIMER 1. It display desired room temperature when `TEMP' button is pushed. `DESIRED TEMP' lamp lights. TEMP or TEMP FAN TURBO ROOM TEMP DESIRED TEMP TIMER Push the `TEMPvw' button. COOLING 3. After a few seconds, display is changed to current room temperature and `ROOM TEMP' lamp lights. FAN SPEED is changed as follows by pushing "FAN SPEED" button. It displays as follows. HIGH MID LOW Push the `FAN SPEED' button. After a few seconds, display is changed to current room temperature. FUNCTION FAN MODE MODE OPERATION 1. `ROOM TEMP' lamp lights. MODE or Push the `MODE' button until `FAN' lamp lights. FAN TURBO COOLING ROOM TEMP DESIRED TEMP TIMER ON/OFF AUTO SWING AUTO SWING AUTO SWING or 1. (left/right direction) There is no change in display. Push the `AUTO SWING' button. [. . . ] These items scrach, crack and discolor surfaces. NOTE To assure continued peak efficiency, condenser coils (weather side of unit) should be checked periodically and cleaned if clogged with soot or dirt from the atmosphere. 17 ELECTRICAL REQUIREMENTS · ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three-prong(grounding) plug for protection against possible shock hazards. If a two-prong wall receptacle is encountered, the customer is required to contact a qualified electrician and have the two-prong wall receptacle replaced with a properly grounded three-prong wall receptacle in accordance with the National Electrical Code. WARNING : To avoid death, personal injury or properly damage due to electrical shock, this unit must be grounded. Do not under any circumstances cut or remove the round grounding prong from the plug. Do not use a two prong adapter. · USE OF EXTENSION CORD Because of potential safety hazards under certain condition, we strongly recommend against the use of an extension cord. [. . . ]