User manual DAEWOO DW-424

[. . . ] · In case of 2 conductor power cord: Connect the grounding wire to a water faucet etc. Make sure that the power cord is unplugged during ground work. Connection of Houses · Attach the drain hose to the drain outlet at the left side of the under base and secure with the clamp provided. Hang the "U" Shaped outlet of the drain hose on the edge of a sink. · Attach the water intake hose to the water inlet located at the left-hand side of the control panel. [. . . ] 7cm above level H. 2 Spin Drying · To open the inner safety lid of the spin bowl, lift up the outer lid, then pull the catch forward and lift upward. · Transfer either the full wash load or portion to the spin bowl commencing with small articles. · Place the removable spin mat over the load to be dried and push lightly downward. (To contain delicated articles within the spin bowl. ) · Close the inner safety lid, then the outer lid. · Set the spin timer to the time recommended in the Laundry Guide. The spin bowl will spin for the time selected, then stop (at position "0"). Caution: Ensure that the spin bowl completely stops before reaching in to remove the wash load. · To remove or reposition clothes during the spin dry cycle, open the outer and inner lids. In this case, the spin bowl will automatically stop as a brake is applied when the outer lid is opened. Note: The pump motor will operate when the spin dry timer is set, irrespective of whether the outer lid is closed or opened. OPERATING INSTRUCTIONS Simultaneous Washing and Spin Drying · Three motors ate fitted to cover washing, spin drying and drainage. This arrangement enables spin drying of a previous wash load and washing of a new wash load to be simultaneously effected. · To do this, set the controls for both "wash" and "spin" modes (see "to wash" and "spin drying"). Laundry Guide Size of Wash Load Full Half & Less Full Half & Less Half & Less Degree of Soiling Heavy Normal Light Normal Light Wash Selection Switch Heavy Normal Hot 60°C Max. Water Temperature Wash Cycle Type of Fabric Fast Coloured Cotton and Linens Nylon and P. P Water Level High Medium Wash Period Spin Period High Medium or Low High Normal Soft Warm 40°C 4-5 mins. 2-3 mins. 2 mins. Delicates Normal to Light Soft Warm 40°C 2-3 mins. 1-2 min. . 3 Control Panel Drain Selector (Pump control) Water Inlet Wash Timer Wash Selector Spin Timer OPERATING INSTRUCTIONS Emptying · Set the valve selector knob to "drain" and the wash timer to 3-5 minutes. · Switch off the electricity at the power point. Lint Filter · Remove the filter frame by pulling it upward (Fig. · Turn the filter inside out and wash the lint off with water (Fig. · Insert the filter frame into the puls-ator hole as it was (Fig. 2-(3)). ( 1) LINT (2) (3) Figure 2. Over flow Strainer · Remove the strainer by pulling it forward (Fig. · Re-install the strainer. Drain Strainer · Remove the drain strainer from the bottom of the tub using a sharp tool such as §^driver (Fig. Figure 3. Pulsator · Should it be necessary to remove the pulsator, say to free an obstruction, first remove the filter frame by pulling it upward, and remove the screw securing the pulsator to the motor shaft Figure 4. · Insert the filter frame into the pulsator hole. 4 POINTS TO REMEMBER · Avoid using excessive amounts of bleach, soap powder or detergent, Use the amount recommended by the respective manufactures. · If the machine is installed in areas subject to freezing temperatures, ensure that it is completely drained after use. [. . . ] · Check that both timers are set to the OFF position ("0"). · Wipe off spillage from wash powder, etc. , and generally wipe over the cabinet with a clean damp cloth. · Remove the hose from water tap. * Design and specifications subject to change without notice. Caution (only for dual voltage model) · Make sure that the electric connector is set for your available voltage before operating the washing machine. [. . . ]