User manual DAEWOO DTQ27U8SC

[. . . ] INSTRUCTION MANUAL Color Television DTQ 27U8SC CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). To prevent electrical shock, match wide blade of plug to wide slot, fully insert the AC plug into a standard 120V~, 60Hz polarized outlet. NOTE Never connect the plug to an electrical source other than one providing 120V~, 60Hz power. [. . . ] 5 If the channel is in memory, then use the CVOLB buttons to delete the channel from memory. 6 If you are going to delete other channel, then press the WCHV buttons until desired channel is selected. 7 Wait 10 seconds, or press the MENU button to return to normal TV viewing. 1 2 3 11 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next 4 5 6 Add/Delete Channels Air 11 This channel is not in memory. Press CH for other channels. Add/Delete Channels Air 11 This channel is in memory. Press CH for other channels. Add/Delete Channels Air 11 This channel is in memory. Press CH for other channels. Press MENU to return to Set-Up menu. Press MENU to return to Set-Up menu. Press MENU to return to Set-Up menu. Displaying the Current Channel 1 To quickly see the current channel number and status, press DISPLAY button on the remote control. The current channel number and status will be displayed. Chapter 3: Operating Your TV 11 Changing the TV's Input Normally, your TV displays the signal coming through the antenna terminal. However, If you've connected another component to your TV(such as a VCR or DVD) using the Video/Audio/Y Cb Cr input, you will want to be able to view the signal from the component. To do this, you will need to switch from the ` TV ' input to the ` AV1, AV2, CVI' Input, as follows. 1 With the TV on, press the MENU button twice, then " Set-Up " menu will appear. 3 Press the CVOLB buttons to change from ` TV ' to ` AV1, AV2, CVI'. 4 Wait 10 seconds, or press the MENU button to return to normal TV viewing. 2 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Select Adjust Next 3-1 Set-Up Language : Input : English AV1 Select Adjust Next 3-2 Set-Up Language : Input : English AV2 3-3 Set-Up Language : Input : English CVI Select Adjust Next Select Adjust Next 12 Chapter 3: Operating Your TV Adjusting Video Settings You may wish to adjust the video settings (e. To do so, follow these directions: 1 With the TV on, press the MENU button. 3 Use the WCHV buttons to select the video setting you wish to adjust. 4 Use the CVOLB buttons to adjust the video setting to the level you prefer. 6 When you are finished, press the MENU button to return to normal TV viewing. 7 Video button on the Remote Controller, can do the same function. 1 2 3 Video Settings : Contrast Brightness Sharpness Color Tint Select Adjust Video Custom Settings : Contrast Brightness Sharpness Color Tint Select Adjust Video Preset Settings : Contrast Brightness Sharpness Color Tint Select Adjust Preset Next Next Next 4 5 6 Contrast Brightness Chapter 3: Operating Your TV 13 Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps : 1 With the TV on, press the MENU button. 2 Press the CVOLB buttons to set the "Settings" to `Preset'. The TV will remember the `Custom' settings you had previously chosen. When you set "Settings" to `Custom' again, your previous custom settings will be restored. 1 2 Video Settings : Contrast Brightness Sharpness Color Tint Select Adjust Video Custom Settings : Contrast Brightness Sharpness Color Tint Select Adjust Preset Next Next Descriptions of video settings The contrast setting controls the relation between the light and black areas of the screen. If the light areas are too bright and are losing details, press the CVOL button; if the picture is gray and lacks contrast, press the VOLB button. The brightness settings controls the overall amount of light in the picture. [. . . ] Please select the Mono mode, the noise and hum should be reduced. Chapter 6 : Adjusting the Sound 25 About AVC This function performs an Automatic Volume Control Function. The sound signal conditions coming out of TV stations are different from each other. When the AVC is on, uniform sound can be ensured regardless of the conditions of TV station. Setting "SURROUND" function You can hear surround sound when stereo broadcasting is receiving or external input sound is stereo. 1 With the TV turned on, press the MENU button until "SOUND" menu will be displayed. [. . . ]