User manual DAEWOO DTQ27S2FCV

[. . . ] INSTRUCTION MANUAL C o l o r Te l e v i s i o n yyy yyy , , , , , , yyy yyy , , , , , , DTQ 25S2FCV DTQ 27S2FCV CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). To provide power to the TV, insert the AC plug into a standard 120V 60Hz polarized outlet. NOTE Never connect the plug to an electrical source other than one providing 120V 60Hz power. [. . . ] If the channel is not in memory, it will be labeled "ERASE, " and the number in the corner will be magenta. 5 Wait 7 seconds, or press MENU twice to exit. 1 2 3 4 12 Chapter 3 : Operating Your TV Changing the TV's Input Normally, your TV displays the signal coming through the antenna terminal. However, if you've connected another component to your TV (such as a VCR) using the Audio/Video Inputs, you will want to be able to view the signal from that component. To do this, you will need to switch from the "TV" input to the "Video" input, as follows; 1 With the TV turned on, Press MENU 2 You will see the Main Menu, Use the VCHW buttons to select SETUP and press CVOLB. 3 Use the VCHW buttons to select INPUT. 5 Wait 7 seconds to return to normal viewing, or press MENU twice. 1 2 3 4 Changing the TV's Input with the remote control 1 1 You can also change the TV/VIDEO setting with the remote control. Press TV/VIDEO button on the remote control to change from TV to VIDEO. Press TV/VIDEO button again to switch back to TV. Displaying the Current Channel 1 1 To quickly see the current channel, press RECALL. The current channel will be displayed briefly. Chapter 3 : Operating Your TV 13 Adjusting Video Settings You may wish to adjust the video settings (e. To do so, follow these directions: 1 With the TV on, press the MENU button. This will allow you to manually adjust the video settings. 1 2 3 4 5 Use the VCHW buttons to select the video setting you wish to adjust. 6 Use the CVOLB buttons to adjust the video setting to the level you prefer. 8 When you are finished, press the MENU button twice to return to normal viewing. 5 6 7 8 14 Chapter 3 : Operating Your TV Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps : 1 Complete steps 1-3 in the "Adjusting Video Settings" section, on the previous page. This will return all video settings to their default levels, as set at the factory. 3 You can also return to the factory settings during normal TV viewing by pressing the AUTO. PICT button on the remote control. The TV will remember the "custom" settings you had previously chosen. When you set AUTO to OFF again, your previous custom settings will be restored. 1 2 3 Descriptions of video settings The contrast setting controls the relation between the light and black areas of the screen. If the light areas are too bright and are losing details, adjust the contrast towards the "-" position; if the picture is gray and lacks contrast, adjust the contrast towards the "+" position. The brightness settings controls the overall amount of light in the picture. If the picture is too bright, adjust the brightness setting towards the "-" position; if the picture is too dark, adjust the brightness towards the "+" position. If the TV shows multiple vertical lines at the edges of an object, adjust sharpness towards the "-" position; if the vertical edges of on-screen objects are fuzzy, adjust sharpness towards the "+" position. If the color is over-saturated, adjust the color towards the "-" position; if the color is washed out, adjust the color towards the "+" position. The tint setting controls the relationship of red and green in a picture. [. . . ] TV-Y : All children This program is designed to be appropriate for all children. Whether animated or liveaction, the themes and elements in this program are specifically designed for a very young audience, including children from ages 2-6 This program is not expected to frighten younger children. Chapter 6 : Additional Features 25 FV : Fantasy Violence V : Violence S : Sexual Situations L : Adult Language D : Sexually Suggestive Dialogue 2. MOVIE RATINGS X NC-17 R PG-13 PG G NR : Adult Movie : No One 17 and Under Admitted : Restricted Under 17 requires accompanying parent or adult guardian. : Parents Strongly Cautioned Some material may inappropriate for children under 13. [. . . ]