User manual DAEWOO DSP-4210GM

[. . . ] To prevent electric shock, use a 3-wire grounding-type plug, and fully insert the plug. To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture. Important safety information Always be careful when using your monitor. To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind when installing, using, and maintaining your machine. Read all safety and operating instructions before operating the PDP monitor. [. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 How to directly check the video system or graphic resolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 How to freeze/pause the picture frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Other OSDs related to auto progress When auto progressing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 When there is no signal after auto detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 When there is an unacceptable signal after auto detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Troubleshooting Before requesting technical support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Plasma display panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Preparation IMPORTANT SAFETY INSTRUCTIONS · When a problem occurs, immediately stop all operations. · Do not place any liquid container on top · Do not place any objects on top of the of the Plasma Monitor. If water spills into the Plasma Monitor, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside, it can cause damage to or premature failure of the unit. · When installing this unit on a wall or ceiling, please consult an Authorized Service Center. Improper mounting can result in personal injury or damage to the unit. · During a lightning storm, do not touch the unit. Doing so may result to an electric shock. · Do not place the Plasma Monitor on sloped or unstable surfaces. The unit may fall off or tip over causing injury and damage. · Do not do anything that might damage the power cable. Damaging the power cable may result in fire or electric shock. · Do not handle the power cord with wet hands. Doing so may cause electric shocks. · Do not overload wall outlets and extension cords. Doing so may result in power failure. · Do not make any modifications. (Never attempt to disassemble this unit yourself) The internal components of this unit is high voltage which may cause electric shocks. · Do not place the Plasma Monitor in sunlight or near heating units. Doing so may cause damage to or cause premature failure of the unit. · Do not cover the ventilation holes. Doing so may cause the Plasma Monitor to overheat, which can cause fire or damage to the internal components. 2 PREPARATION SAFETY PRECAUTIONS · Do not pull or hang the connecting cable. Any damage to the cable can result in electric shocks or fire. · Do not rest the Plasma Monitor on top of other objects. · Do not place the Plasma Monitor in a humid or dusty place or any place near oil, smoke or steam. Built-up dust can increase humidity which might damage the insulation and cause fire. · Do not pull the power cord to remove the power plug from the wall outlet. Doing so can cause fire or electric shock. · If the Plasma Monitor is not in use for a long period of time, unplug the power cord from the wall outlet. It will conserve electricity. · Do not place any heavy objects on the unit. If any foreign objects get inside, please consult an Authorized Service Center. · When inserting batteries, to ensure proper installation, check the polarity. · Do not lean or step on the Plasma Monitor. · Be sure to disconnect all cables before moving the Plasma Monitor. Moving the unit with its cables attached might damage the cables which, in turn, can cause fire or electric shock. · Do not combine a used battery with a new one. VIDEO S-VIDEO DTV/DVD PC · You can watch TV by selecting TV mode on your VCR and tuning to your TV channel. [. . . ] (this monitor cannot be operated by a different remote controller) · unless the picture and sound quality are abnormal, it is a normal sound made when the cabinet contracts slightly due to the change in room temperature. · In case of soft video, wider than 16:9 (cinema-size soft video), the upper and bottom screen may be blank. · Is the monitor affected by cars, street cars, high voltage cables, or neon lights (interfering electric wave or influence electromagnetic wave)? A creaking sound is sometimes made by the main unit. There are blank areas on the upper and bottom screen. There are spots on the screen or the picture waves back and forth excessively. [. . . ]