User manual DAEWOO DPB-280LH

[. . . ] Slide down further to access the battery compartment. REMOTE DISPLAY MODE Indicators (Auto/Quick/Cool/Fan/Dehumidifier/Heat) Lights to indicate the mode selected. AUTO FAN Indicators Lights to indicate the fan speed. FAN DIRECTION Indicators Lights to indicate the fan direction. TIMER Indicators (Include sleep) Lights to indicate the timer function mode. TEMPERATURE & RESERVATION TIME lndicator Lights to indicate the temperature or time. 4 HOW TO INSTALL BATTERIES To install the batteries, follow the procedures below: 1. Insert two "AAA" size Alkaline batteries following the polarity diagram below. TIMER ON/OFF ENTER/ CANCEL TURBO/MILD ­ + BATTERY PRECAUTIONS The precautions below should be followed when using batteries in this device: 1. [. . . ] · If "natural" fan speed is selected, led display of fan speed changes low -> high -> low -> high. But, on dehumidifier mode, the fan speed is fixed to "auto fan speed" to improve dehumidifying efficiency. METHOD BY USING REMOTE CONTROLLER 1. Press "fan speed" button of remote controller, the functions are the same as the methods by using main control. 8 TO SELECT THE FAN DIRECTION - Remote controller is only available. 1. Press fan direction button to select fan direction · Press desired fan direction button, "UP · DOWN" or "LEFT · RIGHT" control louver moves, press again to stop FAN DIR. 2. "UP · DOWN" Up · down louver moves "LEFT · RIGHT" Left · right louver moves FAN DIR. 3. "UP · DOWN, LEFT · RIGHT" · Up · down, left · right louver move together NOTES: Do not touch or try to adjust louver by force when the louvers move automatically. When the desired hour is reached, the unit will turn on to the selected mode. 4. Press the ENTER button to input the setting into memory; the unit will beep, the TIMER indicator will light on the unit and the TIMER indicator on the remote will light to indicate the unit is in the timer mode. NOTE : Press the ENTER button within 5 seconds of selecting the desired time. If mote than 5 seconds elapse, steps 3 and 4 must be repeated. TO SET SLEEP MODE - Press sleep mode button while air conditioner is on 1. · Press the sleep mode button, 4 indicator appears in the display. The unit will turn off after 4 hours from now · You can select fan direction · You can select auto, low, middle, high, natural of fan speed(at first fan speed is low) AUTO NOTES: To set sleep mode is not available on fan mode and quick mode 10 TO SET THE FUNCTION MODE AUTO MODE METHOD BY USING MAIN CONTROL 1. SELECT AUTO MODE BY PRESSING MODE BUTTON · AUTO -> QUICK -> COOL -> FAN -> DEHUMIDIFIER -> HEAT is sequently selected by pressing "MODE" button · Desired temperature is available from 24°C to 28°C METHOD BY USING REMOTE CONTROLLER 1. SELECT AUTO MODE BY PRESSING MODE BUTTON "Auto mode" operation gives you the most comfortable airs by adjusting temperature, humidity and fan speed automatically according to the room conditions. AUTO NOTES: If it is necessary, select fan speed or fan direction QUICK MODE METHOD BY USING MAIN CONTROL 1. SELECT QUICK MODE BY PRESSING MODE BUTTON Cooling: room temperature is low METHOD BY USING REMOTE CONTROLLER 1. SELECT QUICK MODE BY PRESSING MODE BUTTON "Quick mode" operation allows you to make the room cool(or warm) quickly according to the room conditions Heating: room temperature is high NOTES: If it is necessary, select fan direction · Fan speed and temperature control is not available because fan speed and temperature is set automatically on quick mode 11 COOL MODE MOTHOD BY USING MAIN CONTROL 1. SELECT COOL MODE BY PRESSING MODE BUTTON Desired temperature is available from 18°C to 32°C To make room cool and comfortable, adjust desired room temperature by using temperature button. METHOD BY USING REMOTE CONTROLLER 1. SELECT COOL MODE BY PRESSING MODE BUTTON AUTO NOTES: If it is necessary, select fan speed or fan direction FAN MODE METHOD BY USING MAIN CONTROL 1. SELECT FAN MODE BY PRESSING MODE BUTTON NOTES: Fan speed changes as follows by pressing fan speed button on fan mode low -> middle -> high -> natural METHOD BY USING REMOTE CONTROLLER 1. SELECT FAN MODE BY PRESSING MODE BUTTON ¡ NOTES: If it is necessary, select fan speed or fan direction 12 DEHUMIDIFIER MODE METHOD BY USING MAIN CONTROL 1. SELECT DEHUMIDIFIER MODE BY PRESSING MODE BUTTON This mode can be selected in case you feel uncomfortable due to high humidity even though room temperature is not high. METHOD BY USING REMOTE CONTROLLER 1. SELECT DEHUMIDIFIER MODE BY PRESSING MODE BUTTON NOTES: If it is necessary, select fan direction · Fan speed control is not available because fan speed is set automatically on dehumidifier mode HEAT MODE METHOD BY USING MAIN CONTROL 1. SELECT HEAT MODE BY PRESSING MODE BUTTON Desired temperature is available from 18°C to 32°C To make room warm and comfortable, adjust desired room temperature by using temperature button. METHOD BY USING REMOTE CONTROLLER 1. SELECT HEAT MODE BY PRESSING MODE BUTTON NOTES: If it is necessary, select fan speed or fan direction 13 ECONOMY MODE - MAIN CONTROL IS ONLY AVAILABLE Select by pressing "economy" button 1. [. . . ] Wait 3 minutes for the unit to operate. The compressor does not turn on. (no cool air at cooling no warm air at heating) When the unit is first plugged in and turned on, the compressor will delay turn on for 3 minutes. If the unit is turned off and then immediately back on, the compressor will delay for 3 minutes. Unit is located near a heat source (heater, stove, etc. ) A door or window is open. [. . . ]