User manual DAEWOO DMB-3003LH

[. . . ] SAFETY INSTRUCTIONS PLEASE READ THE FOLLOWING SAFETY INSTRUCTIONS BEFORE INSTALLING AND OPERATING THE UNIT: This air conditioner meets strict safety and operating standards. The installer of this unit must install or service this unit so it operates safely and efficiently. Precautions When Wiring: · Do not plug in the unit until all connections (tubing, drain hose, mounting, etc. ) have been made and double-checked. · High voltages are present in this unit and are very dangerous. Improper connections or inadequate grounding can cause accidental injury. [. . . ] The On LED will light on the indoor unit and "ON" will light in the remote display. To select the various modes and settings, read the following pages. EMERGENCY/REMOTE Switch THREE MINUTE COMPRESSOR DELAY · After turning the indoor unit on and setting it for air conditioner operation, the compressor (outdoor unit) will not come on for three minutes. This is a feature that will protect the compressor from damage due to quick start and stops. EMR. REMOCON 8 HOW TO INSTALL BATTERIES To install the batteries, follow the procedures below: 1. Insert two "AAA" size Alkaline batteries following the polarity diagram below. TIMER ON/OFF ENTER/ CANCEL TURBO/MILD ­ + BATTERY PRECAUTIONS The precautions below should be followed when using batteries in this device: 1. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer's directions). CELSIUS TO FAHRENHEIT CONVERSION CHART CELSIUS 18 19 20 21 22 23 24 25 FAHRENHEIT 64. 4 66. 2 68 69. 8 71. 6 73. 4 75. 2 77 CELSIUS 26 27 28 29 30 31 32 FAHRENHEIT 78. 8 80. 6 82. 4 84. 2 86 87. 8 89. 6 CAUTION-IN CASE OF OPERATING TWO UNITS the operation mode of the remote controller CASE I indoor unit B1 indoor unit B2 Operation Fan Heating Heating Fan Cooling Heating Heating Cooling Fan Cooling Cooling Fan CASE II Cooling Cooling Cooling Dehumidification Dehumidification Cooling Good Heating Heating No Good As shown above, When the "CASE I" is selected, only the indoor unit which is received the first signal from the remote controller operates and the other indoor unit doesn't operate. in that case, try to select one out of the "CASE II" again. 9 ­ + TO SET AUTO MODE This unit will automatically operate the unit according to its surroundings while in the Auto mode. All you have to set is the desired temperature and it will control the fan, coolness and dehumidifier. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. The desired temperature can be changed up or down 1 degree from the actual room temperature. Then the unit will automatically operate. AUTO TO SET QUICK MODE To set this unit to cool at the highest power, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. Press the MODE button until the Quick indicator appears in the display. 3. The unit will then start cooling the room at the highest power. TO SET COOL MODE To set the unit to cool the room to a desired temperature, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. The desired temperature can be changed up to 32°C and down to 18°C. Press the MODE button until the Cool indicator appears in the display. 4. To select the fan speed, press the FAN SPEED button until the desired speed appears in the display (see below). FAN SPEEDS AUTO "AUTO" "" "" "" "NATURAL" The fan will automatically select the fan speed. The fan will randomly cycle through the speeds simulating a cool breeze. 10 TO SET ONLY FAN MODE To operate only the fan so the unit will circulate the air, proceed as follows: 1. [. . . ] Insert cleaned or new black filters back into the unit. NOTES: · The filters should be changed every 6 months. · After getting rid of vinyl in the filter (Deodorizing and Electrostatic), use it. CLEANING THE INDOOR COVER To clean the indoor cover, follow the procedures below: 1. Remove the left and right side to open the indoor cover upward by two hands. (Remove it when cleaning. ) NOTES: · Wipe the indoor cover with soft sponge or soft cloth. [. . . ]