User manual DAEWOO 5160 [FOR GODREJ]

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Contact Installer if Necessary: The installation instructions are for a experienced installer. If you are not an experienced installer, contact a local installer for help. If you require help with service, contact your certified dealer or Daewoo Electronics for additional instructions. [. . . ] Then the unit will automatically operate. AUTO 9 TO SET QUICK MODE To set this unit to cool or heat at the highest power, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. The unit will then start cooling or heating the room at the highest power. TO SET COOL MODE To set the unit to cool the room to a desired temperature, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. Press the MODE button until the Cool indicator appears in the display. 3. The desired temperature can be changed up to 32°C and down to 18°C. 4. To select the fan speed, press the FAN SPEED button until the desired speed appears in the display (see below). FAN SPEEDS AUTO "AUTO" "" "" "" "NATURAL" The fan will automatically select the fan speed. The fan will randomly cycle through the speeds simulating a cool breeze. 10 TO SET FAN ONLY MODE To operate only the fan so the unit will circulate the air, proceed as follows: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. To select a fan speed, press the FAN SPEED button until the desired speed appears in the display (see below). FAN SPEEDS "" "" "" "NATURAL" The fan will operate on low speed. The fan will randomly cycle through the speeds simulating a breeze. NOTE: · If "NATURAL" is selected, the NATURAL" indicator on the indoor unit will light. TO SET DEHUMIDIFIER MODE Select this mode when there is high humidity. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. Press the MODE button until the Dehumidifier indicator appears in the display. 3. The desired temperature can be changed up to 32°C and down to 18°C. 11 TO SELECT THE FAN DIRECTION Regardless of the mode the unit is set for, the fan direction can be changed so it moves up and down, left and right or both. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and "ON" will light in the remote display. See chart below for detailed information on each of the three settings. FAN DIR. FAN DIR. FAN DIR. Normal air direction. 12 TO SET ON TIMER MODE This unit can be set to automatically turn on after a predetermined amount of hours (up to 24) in the order of 0. 5, 1, 1. 5, 2, 2. 5, 3, 3. 5, 4, 5, 6, 8, 10, 12, 16, 20, 24. Press the ON/OFF button of timer on the remote control to set the on timer mode, "HOUR" and "ON" on the remote display will be displayed and "TIMER" will be flicked. When you increase to press "ON/OFF" you will get desired time. Then, if pressing "ENTER/CANCEL" button, ON TIMER Mode will be started. If you want to stop ON TIMER Mode, please press "ENTER/CANCEL" again. While the unit is off, press the TIMER ON button; the display will light waiting input for the timer, but the actual unit will not turn on. [. . . ] · In a lightning or thunder storm, immediately unplug it from the wall. 16 TROUBLESHOOTING GUIDE Before requesting service, please refer to the chart below for possible solutions: SYSPTOMS No power. POSSIBLE CAUSE Power failure. EMERGENCY/REMOTE switch is not set to REMOTE. POSSIBLE SOLUTIONS Restore the power Contact electrician to install new outlet. Wait 3 minutes for the unit to operate. The compressor does not turn on. (no cool air at cooling) (no heat air at heating) When the unit is first plugged in and turned on, the compressor will delay turn on for 3 minutes. [. . . ]