User manual DAEWOO 1500P

[. . . ] Use only with motorized nozzle model RPB-220. SAVE THESE INSTRUCTIONS 2 R1500P(EN-TACONY)-9. 3 2004. 9. 39:55AM 4 CONTENTS DESCRIPTION AND USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4~5 HOW TO POWER NOZZLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6~9 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 REPLACING BAGS & FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To reinsert the wand into the power nozzle, simply press the wand back into the neck of the power nozzle. The wand will then "click" back into place. Diagram 6 Diagram 7 Diagram 5 Carpet Height Notes: When using the power nozzle, start on the "auto" setting. If pushing the power nozzle forward feels sluggish or hard to push, then adjust to a higher setting (i. e. If the power nozzle feels very easy to push, you may want to lower the power nozzle for more effective cleaning. The "Auto" setting is the recommended setting for hard floor surfaces (i. e. tile, vinyl, wood). 6 R1500P(EN-TACONY)-9. 3 2004. 9. 39:55AM 8 OPERATION 5. Warning Light Your power nozzle comes equipped with a circuit breaker safety system that protects it from a jammed power nozzle situation. Common items that cause jammed brushrolls include socks, excessive threads, corners of area rugs, etc. The warning indicator light on top of the unit (see diagram 8) will change from green to red should this condition occur. Warning Light If the circuit breaker trips: a. Turn off the vacuum cleaner and power brush then unplug the power cord. Locate the circuit breaker switch on the back of the power nozzle and press it to reset the breaker (see diagram 9). When the unit is turned back on, the warning light should be green and ready to go. If the breaker trips again, repeat steps a-c again to Circuit Breaker Switch correct the problem. If this does not correct the problem, contact your authorized vacuum cleaner retailer for further assistance. Diagram 9 Diagram 8 MAINTENANCE AND CARE 1. Removing the Brushroll IMPORTANT: Before performing any maintenance work on the power nozzle, always unplug the vacuum cleaner and disconnect the wand. Your brushroll may need to be removed at times, for example, to cut threads that have become tangled around the brushroll or to replace the belt (see "Replacing the Belt"). To remove the brushroll, turn the unit over and lift off the metal bottom plate by first unscrewing the two bottom plate screws located by the rear wheels (see diagram 10). Pull out the belt cover guard (see diagram 11) and pull the brushroll out. Diagram 10 Diagram 11 To reinstall the brushroll, reinsert the brushroll back into the unit (make sure the belt is attached properly). Then, place the metal bottom plate back onto the unit (insert the front end of the bottom plate first). Re-insert the two bottom plate screws and secure. Bottom Plate Screws 7 R1500P(EN-TACONY)-9. 3 2004. 9. 39:55AM 9 MAINTENANCE AND CARE 2. Replacing the Power Nozzle Belt IMPORTANT: Before performing any maintenance work on the power nozzle, always unplug the vacuum cleaner and disconnect the wand. To replace the power nozzle belt, you must first remove the brushroll (see "Removing the Brushroll"). [. . . ] If the plug should still fail to fit, contact an electrician to replace the obsolete outlet. Do not defeat the safety purpose of the polarized plug. 10 R1500P(EN-TACONY)-9. 3 2004. 9. 39:55AM 12 REPLACING VACUUM BAG & FILTERS REPLACING THE VACUUM BAG Full Bag Indicator Vacuum bag Holder Dust Cover · Turn canister off, remove · Pull the shutter of the vacuum bag. · Hold the cover while removing the vacuum bag from the vacuum bag holder. · Insert the new bag. NOTE: We recommend the vacuum bag is changed when indicator is RED or suction power is weak. [. . . ]