User manual DA-LITE WM-VC INSTALLATION SHEET E-466

[. . . ] attach two ceiling mount brackets to the screen case as shown in figure 2. do not remove the wall mount bracket, even if you are not using it for mounting. be sure the ceiling has adequate reinforcement to attach a hook anchor. [. . . ] attach ceiling hook brackets as provided to the screen case as shown in figure 3. The brackets can be attached anywhere within 12" of the end of the case. attach an s-hook or similar fastener to the hole in the bracket. 2 CeIlIng hook bRaCkeT 1/4 x 5/8" flaT head sCReW 1/4 x 5/8" flaT head sCReW sToP sCReW 6-3/8" Wall mounT bRaCkeT 2-5/16" Case 2-9/16" hook 5-11/16" FIGURE 1 CeIlIng mounT bRaCkeT FIGURE 2 FIGURE 3 ELECTRICAL INSTALLATION Internal wiring has been completed at the factory. Installer must route power to the wall switch and to the junction box located on the left end of the screen case. standard installation is for a single 120VaC or 240VaC wall switch to control the screen. Wiring diagrams for the built-in VPI and low voltage control are included in these instructions. Refer to additional instructions for the external VPI, external low voltage control, sCb-100 and sCb-200. NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/ CSA C22. 1 and the National Electric Code (NEC), NFPA 70. SCREEN AdjUSTMENT screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory. If it's necessary to adjust for more or less drop follow the steps below. !Therefore, it is advised to wire the switch or provide a 3-conductor connection that is accessible. GREEN (GROUND) BLACK (HOT) WHITE (COMMON) POWER INPUT 120VAC / 60HZ GROUND­MUST BE CONNECTED TO BUILDING GROUND 240V WIRING DIAGRAM WITH OPTIONAL BUILT-IN LOW VOLTAGE CONTROL BLUE (COMMON) BROWN (HOT) 240VAC 50HZ GREEN OPTIONAL IR AND RF REMOTE CONTROL LOW-VOLTAGE WALL SWITCH UP DN UP GND +5V MOTOR Rj9 Rj9 STOP DOWN 3-POSITION SWITCH Rj9 GROUND TO CASE UP +5V COM DN GROUND­MUST BE CONNECTED TO BUILDING GROUND GREEN FRONT BACK SPLITTER DRY CONTACTS ILT Rj9 PIN-OUTS (TAB IS FACING UP) IR or UP GND COMMON +5V DN or DATA BLACK RED GREEN WHITE IMPORTANT NOTE: The wall switch is ReQuIRed to make any limit switch adjustments, eVen if a third party control system is used. Therefore, it is advised to wire the switch or provide a 4-conductor connection that is accessible. 5 TROUBLESHOOTING Visit www. da-lite. com/products/tutorials. php to find installation and troubleshooting tutorials. You will also find a link to Live Chat for interactive support and you can contact us by email at info@da-lite. com or by phone at (800) 622-3737 or (574) 267-8101 with any troubleshooting questions. SYMPTOM 1. "Down" Position Check for power across black and white leads. "Up" Position Check for power across red and white leads. (b) blown fuse. (d) no power to operating switch or junction. Power at junction box (e) Thermal overload tripped. (a) "Down" limit switch out of adjustment (a) "Up" limit switch out of adjustment (a) gear noise. (a) Replace motor assembly. (a) defective brake. (a) Replace motor assembly. 6 LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS da-lite screen Company, Inc. warrants its products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser provided they are properly operated according to da-lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory. [. . . ] This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered with or repaired by a person other than authorized da-lite personnel. da-lite's sole obligation under this warranty shall be to repair or to replace (at da-lite's option) the defective part of the merchandise. If it is necessary for the dealer to return the screen or part to da-lite, transportation expenses to and from da-lite are payable by the purchaser and da-lite is not responsible for damage in shipment. [. . . ]