User manual DA-LITE TENSIONED PROFESSIONAL ELECTROL

[. . . ] The Da-Lite Difference. Instruction Book for DA-LITE SCREEN COMPANY, INC. 3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 www. da-lite. com e-mail: info@da-lite. com tensIoned professIonal electrol® PRE-INSTALLATION 1. Make sure to recheck measurements of screen location before installation. Remove the retainer screws from the slat bar before the case has been installed (Fig. [. . . ] Test by raising picture surface approximately two feet, then lower again. Test by raising picture surface approximately two feet, then lower again. WHEN ADJUSTING AND TESTING, BE PREPARED TO STOP SCREEN QUICKLY AS SERIOUS DAMAGE MAY OCCUR. WHITE ADJUSTMENT KNOB "DOWN" SHIPPING BRACE (NOT ON 4-1/2" ROLLER) YELLOW OR RED ADJUSTMENT KNOB "UP" SLAT FIGURE 3 2 TENSIONED PROFESSIONAL ELECTROL® INSTALLATION 9-1/2" 11-5/16" Reinforced Top Motor End Electrical Outlet Box SUGGESTED METHODS OF INSTALLATION CEILING TYPE HANGER 2" MOULDING PICTURE SURFACE 1" x 3" CLEAT PICTURE SURFACE PICTURE SURFACE RAFTERS WALL TYPE HANGER CEILING MOUNT WITHOUT HANGERS Screen case is placed flush with the wall and ceiling and held in position by moulding securely attached to the wall. RECESSED ABOVE CEILING Other methods of installation will suggest themselves in new buildings where it would be an easy matter to provide a recess for the screen to conceal it when not in use. Do not seal in--allow access. PICTURE SURFACE WALL OR CEILING MOUNT WITH HANGERS Wall type hangers and ceiling type hangers are standard equipment. Useful for recessed installations. 3 FOR EXPOSED INSTALLATION If the screen is to be mounted in an exposed position, it may be covered with finished plywood, veneer, paneling, plastic wall covering or a valance. TENSIONED PROFESSIONAL ELECTROL® INSTALLATION 120V WIRING DIAGRAM IN MULTIPLE CONTROL INSTALLATIONS THE SWITCH IS REPLACED BY THE LOW VOLTAGE CONTROL, OPERATED FROM PUSH BUTTON STATIONS. TO JUNCTION BOX MOUNTED IN SCREEN CASE, IN WHICH INTERNAL WIRING TERMINATES IN WHITE, BLACK, AND RED LEADS. RED (UP) BLACK (DOWN) WHITE (COMMON) GREEN (GROUND) WHITE (COMMON) BLACK (DOWN) GREEN (GROUND) BLACK (DOWN) UP OFF DOWN SIDE VIEW OF SWITCH & BOX RED (UP) AC COMMON AC HOT 115V. BLACK WITH YELLOW OPERATING SWITCH, SWITCH BOX, AND PLATE FURNISHED WITH SCREEN. (SPDT WITH CENTER OFF) GREEN (GROUND) GREEN (GROUND) RED (UP) MOTOR THIS SWITCH CANNOT BE USED WITH L. V. C. CONTACT THE FACTORY FOR FURTHER INFORMATION. 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH: Da-Lite offers two styles of 240 volt wall switches for standard operation. Please see wiring diagram in wall switch box included with screen. 4 TROUBLESHOOTING SYMPTOM 1. "Down" Position Check for power across black and white leads. "Up" Position Check for power across red and white leads. Power at junction box (d) Thermal overload tripped. See installation instructions (a) Replace motor assembly. (a) Defective brake. (a) Replace motor assembly. RESTORING LOST ROLLER WRAP 1. Remove tape and strap. 5 6 LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Da-Lite Screen Company, Inc. warrants its products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory. [. . . ] In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137 Warsaw, IN 46581-0137 (574) 267-8101, (800) 622-3737 , , . IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH DA-LITE'S WRITTEN INSTRUCTIONS. Keep your sales receipt to prove the date of purchase and your original ownership. Printed in U. S. A. 7 33871 3/10 [. . . ]