User manual DA-LITE MOTORIZED SCENIC ROLLER SCREEN

[. . . ] The POWER In PRESENTATION PRODUCTS Instruction Book for DA-LITE SCREEN COMPANY, INC. 3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 www. da-lite. com e-mail: info@da-lite. com MOTORIZED SCENIC ROLLER SCREEN IMPORTANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. [. . . ] Check the cables to make sure they are winding on the motor and roller pulleys properly. !With screen in complete unrolled position, examine the screen surface carefully. If fabric does not hang flat, loosen the nuts on the eyebolts of the black clamps. Several clamp heights may be adjusted depending on the severity of the hang. After adjustment, tighten the nuts against the underside of the frame. Do not bump screen with ladders, scenery, etc. 2 MOTORIZED SCENIC ROLLER INSTALLATION 120V WIRING DIAGRAM WHITE - (COMMON) RED - (UP) BLACK - (DOWN) GREEN - (GROUND) WHITE - (COMMON) RED - (UP) BLACK - (DOWN) GREEN - (GROUND) SAFETY SWITCH WHITE - (COMMON) BLACK - (HOT) GREEN - (GROUND) BROWN - OUT OF CONTROLLER RED - OUT OF CONTROLLER WHITE BLACK WHITE - (COMMON) RED - (UP) BLACK - (DOWN) POWER INPUT 120VAC / 60HZ RED - OUT OF CONTROLLER BROWN - OUT OF CONTROLLER FRONT BACK OF OF WALL WALL SWITCH SWITCH UP STOP DOWN NOTE: 20-24AWG WIRE RECOMMENDED FOR CONNECTING WALL SWITCH TO SYCHRONIZATION CONTROLLER RED - (UP) BLACK - (DOWN) WHITE - (COMMON) OPTIONAL RF REMOTE CONNECTION NOT USED 240V WIRING DIAGRAM BLUE - (COMMON) BLACK - (UP) BROWN - (DOWN) GREEN/YELLOW - (GROUND) BLUE - (COMMON) BLACK - (UP) BROWN - (DOWN) GREEN/YELLOW (GROUND) NOTES: 1. FUSE RATED 15A - 250VAC SAFETY SWITCH POWER INPUT 240VAC / 50HZ 3. 6 AMPS BROWN - OUT OF CONTROLLER RED - OUT OF CONTROLLER BLACK BLUE - (COMMON) BLACK - (UP) BROWN - (DOWN) BLUE - (COMMON) BROWN - (HOT) WHITE GREEN/YELLOW (GROUND) FRONT BACK OF OF WALL WALL SWITCH SWITCH UP STOP DOWN BLACK RED - OUT OF CONTROLLER BROWN - OUT OF CONTROLLER NOTE: 20-24AWG WIRE RECOMMENDED FOR CONNECTING WALL SWITCH TO SYCHRONIZATION CONTROLLER RED - (UP) BLACK - (DOWN) WHITE - (COMMON) OPTIONAL RF REMOTE CONNECTION NOT USED 3 LIMIT SWITCH ADJUSTMENT The stop positions of the screen are preset at the factory. If adjustments are necessary, the limit switch screws located at the end of each motor can adjust the stop positions. Adjustments should be made in small increments by turning the adjustment screws a half turn at a time. SCREEN DROPS TOO FAR: Left motor (as viewed from audience side): Turn the white limit switch screw clockwise to decrease the amount of fabric drop. Right motor (as viewed from audience side): Turn the yellow limit switch screw clockwise to decrease the amount of fabric drop. After adjusting the limit screws on both motors, run the screen down to test the stop position. SCREEN DOES NOT DROP ENOUGH: Left motor (as viewed from audience side): Turn the white limit switch screw counterclockwise to increase the amount of fabric drop. Right motor (as viewed from audience side): Turn the yellow limit switch screw counterclockwise to increase the amount of fabric drop. After adjusting the limit screws on both motors, run the screen down to test the stop position. SCREEN TRAVELS UP TOO FAR: Left motor (as viewed from audience side): Turn the yellow limit switch screw clockwise to decrease the amount of travel. [. . . ] After adjusting the limit screws on both motors, run the screen up to test the stop position. Repeat until the desired position is set. 4 LIMIT SWITCH ADJUSTMENT FIG. 3 YELLOW - UP LIMIT CLOCKWISE = LESS UP TRAVEL COUNTERCLOCKWISE = MORE UP TRAVEL MOTOR 1 MOTOR 2 WHITE - DOWN LIMIT CLOCKWISE = LESS DOWN TRAVEL COUNTERCLOCKWISE = MORE DOWN TRAVEL TOP VIEW - AUDIENCE SIDE Printed in U. S. A. 5 84222 Rev. [. . . ]