User manual DA-LITE DESIGNER DA-TAB ELECTROL

[. . . ] To reduce the risk of electric shock, do not disassemble this appliance. Incorrect reassembly can cause electric shock when the appliance is used subsequently. The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury to persons. SAVE THESE INSTRUCTIONS 1 PRE-INSTALLATION Before proceeding with the installation of the screen, please read the installation and operations instructions thoroughly! !Lift front cover up approximately 1/2" and pull away from back of screen. [. . . ] Then proceed to use the two "D" rings that are factory mounted to the top of the case to hang the case securely. Make sure to review your electrical installation checklist and wiring diagrams (included) for either 120 volt switch, 220/240 volt switch or low voltage control. NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/ CSA C22. 1 and the National Electric Code (NEC), NFPA 70. A 6" 5-1/2" B 5-1/2" 7" PICTURE SURFACE A = FABRIC WIDTH + 14" B = FABRIC WIDTH 7" 3 DESIGNER DA-TAB ELECTROL® INSTALLATION 120V WIRING DIAGRAM EXTERNAL WIRING TO BE COMPLETED BY INSTALLER. TO JUNCTION BOX, MOUNTED IN SCREEN CASE, IN WHICH INTERNAL WIRING TERMINATES IN WHITE, BLACK AND RED LEADS. DOWN WHITE LIMIT SWITCH KNOB OPERATING SWITCH, SWITCH BOX, AND PLATE FURNISHED WITH SCREEN. MAX BLACK WITH YELLOW MOTOR BLACK DOWN SIDE VIEW OF SWITCH AND BOX WHITE COMMON UP RED LIMIT SWITCH KNOB IN MULTIPLE CONTROL INSTALLATIONS THIS SWITCH IS REPLACED BY THE LOW VOLTAGE CONTROL, OPERATED FROM PUSH BUTTON STATIONS. ROCKER BLACK SWITCH UP OFF DOWN RED THIS SWITCH CANNOT BE USED WITH LVC. NOTE: A single switch cannot be used to operate more than one screen. Contact the factory for further information. RED UP FIGURE 3 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH: Da-Lite offers two styles of 240 volt wall switches for standard operation. Please see wiring diagram included in wall switch box included with screen. SCREEN ADJUSTMENT FOR 120V AND 220V/240V SCREENS Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory. If it's necessary to adjust for more or less drop follow the steps below. Lift front cover up approximately 1/2" and pull away from back of screen. SETTING THE DOWN LIMIT POSITION TO REDUCE SCREEN DROP: Turn the white limit switch screw clockwise to decrease the amount of screen drop. If the screen drops too far, raise the screen about one foot and adjust the limit switch again. TO INCREASE SCREEN DROP: Turn the white limit switch screw counterclockwise to increase the amount of screen drop. If the screen does not drop enough, raise the screen about one foot and adjust the limit switch again. At least 1-1/2 wraps of fabric must remain on the roller. 4 TROUBLESHOOTING SYMPTOM 1. "Down" Position Check for power across black and white leads. "Up" Position Check for power across red and white leads. (b) Blown fuse. (d) No power to operating switch or junction. Motor hums. Power at junction box (e) Thermal overload tripped. (a) "Down" limit switch out of adjustment (a) "Up" limit switch out of adjustment (e) Let motor cool down for 15 minutes. [. . . ] THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY. Any implied warranties of fitness for use, or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives you specific legal rights, and you may also have other rights, which vary from state-to-state. NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE. [. . . ]