User manual DA-LITE ADVANTAGE ELECTROL

[. . . ] Replace junction box cover and secure with 2 screws. SCREEN AND ROLLER ASSEMBLY INSTALLATION If your screen was shipped with the motor and roller already installed, proceed to step 6. To install screen and roller assembly, insert the motor end into the motor mount bracket as shown in Fig. Loosen (but do not remove) two 1/4-20 nuts securing pin end bracket (stage left) to the case housing. Insert the motor end square shaft into the motor end bracket and secure with the clip. [. . . ] The red wire from the VPI is the "signal" and the black wire from the VPI is the "ground" . Connect the wires from the VPI that are labeled "Low Voltage Connection" to the end of the extended screen trigger wires above. 240V WIRING DIAGRAM WITH OPTIONAL BUILT-IN LOW VOLTAGE CONTROL BLUE (COMMON) BROWN (HOT) 240VAC 50HZ GREEN OPTIONAL IR AND RF REMOTE CONTROL LOW-VOLTAGE WALL SWITCH UP DN UP GND +5V MOTOR RJ9 RJ9 STOP DOWN 3-POSITION SWITCH RJ9 GROUND TO CASE UP +5V COM DN GROUND­MUST BE CONNECTED TO BUILDING GROUND GREEN FRONT BACK SPLITTER DRY CONTACTS ILT RJ9 PIN-OUTS (TAB IS FACING UP) IR or UP GND COMMON +5V DN or DATA BLACK RED GREEN WHITE IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used. Therefore, it is advised to wire the switch or provide a 4-conductor connection that is accessible. FIGURE 8 5 SCREEN ADJUSTMENT FOR 120V SCREENS WITHOUT BUILT-IN LOW VOLTAGE CONTROL Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner: Remove two screws to remove access door. NOTE: Use a screw driver or 5/32" Allen wrench to make adjustments. When the screen stops, turn the white "down" limit knob (Fig. 1) one turn counterclockwise. Test by raising picture surface approximately two feet, then lower again. Test by raising picture surface approximately two feet, then lower again. Repeat until desired picture surface position is attained. WHITE ADJUSTMENT KNOB "DOWN" MOTOR POWER CONNECTOR MOTOR MOTOR MOUNT BRACKET BLACK ADJUSTMENT KNOB "UP" FIGURE 1 SCREEN ADJUSTMENT FOR 220/240V SCREENS WITHOUT BUILT-IN LOW VOLTAGE CONTROL Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner: NOTE: Use a screw driver or 5/32" Allen wrench to make adjustments. When the screen stops, turn the white "down" limit knob (Fig. 2) one turn counterclockwise. Test by raising picture surface approximately two feet, then lower again. Test by raising picture surface approximately two feet, then lower again. Repeat until desired picture surface position is attained. MOTOR POWER CONNECTOR MOTOR WHITE ADJUSTMENT KNOB "DOWN" MOTOR MOUNT BRACKET RED ADJUSTMENT KNOB "UP" FIGURE 2 6 SCREEN ADJUSTMENT FOR 120V SCREENS WITH A BUILT-IN LOW VOLTAGE CONTROL OR VPI 1. Locate the wall switch and remove the cover plate from the 3-button wall switch and remove the switch from the junction box. To adjust the down limit switch, press and hold the down tactile button until the LED on back of switch turns solid red. If you travel to far down you can press the up to move the screen upward. If you press and let go of either up or down button the motor will do a small jog in that direction for finer adjustment of screen. Once desired position is reached turn switch over press and hold down tactile button until the LED on back of switch blinks red twice. To adjust the up limit switch, press and hold the up tactile button until the LED on back of switch turns solid green. [. . . ] If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment. To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses. THISWARRANTYISINLIEUOFALLOTHERWARRANTIES, EXPRESSORIMPLIED, INCLUDINGWARRANTIESASTOFITNESSFORUSEANDMERCHANTABILITY. Any implied warranties of fitness for use, or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. [. . . ]