User manual COMET LABS GS5+

[. . . ] 5 Ports Gigabit Nway Ethernet Switch Model-nr : GS5+ User's Manual (English version) FCC Warning This device has been tested and found to comply with limits for a Class B digital device, pursuant to Part 2 and 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiates radio frequency energy and, if not installed and used in accordance with the user's manual, may cause interference in which case user will be required to correct the interference at his own expense. [. . . ] 5 Chapter 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 I. To connect the Switch to PCs, servers, and other network devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chapter 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 I. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chapter 1 - Specifications Introduction The Switch provides 5 10/100/1000Mbps NWAY RJ-45 ports. It was designed for easy installation and high performance in an environment where traffic on the network and the number of user increase continuously. With newest Gigabit chip set, eTen 9" Gigabit Ethernet switch can fully support highest speed without hanging on problem even when Full-dueplex full loaded. The switch also provides automatic crossover detection functionality on each port. It is simple and friendly to up-link to another switch without crossover cable. The compact rigid desktop size was specifically designed for ROBO (Remote Office & Branch Office) and medium to large workgroups. The Switch can be installed where space is limited; moreover it provides smooth network migration and easy upgrade to network capacity. The 9" size can be rack-mount on 10" or 19" cabinet. Key Features l l l l l l l l l l l l l l Complies with the IEEE802. 3 Ethernet, IEEE802. 3u Fast Ethernet and IEEE 802. 3ab Gigabit Ethernet Standards Provides five 10/100/1000Mbps Gigabit switching ports Performs full wire-speed switching with Head of Line (HOL) blocking prevention. Non-blocking & Non-head-of-line blocking full wire speed forwarding. All ports provide Auto-Negotiation and Auto -MDI/ MDI-X functions Supports flow control: Back pressure for Half-duplex and IEEE 802. 3x for Full-duplex mode Status LED: Power per set and 1000M, Link/Activity Configurable to 10 full/half duplex, 100 full/half duplex and 1000 full/half duplex for each port 9" inch compact size, and can be rack-mount to 10" and 19" with bracket. -2- Chapter 2 Package Contents Before you start to install the Switch, please verify your package contain the following items: One 9" Gigabit Ethernet Switch One AC Power Cord One User's Manual Note: If any of these items is found missing or damaged, -3- please contact your local supplier for replacement. Chapter 3 Front Panel Layout I. Ports - 5 RJ-45 Gigabit Switch Ports There are 5 RJ-45 connectors on the front panel for connecting to servers, workstation or other devices. The Switch provides 5 10/100/1000Mbps switching ports that could sense the 10/100/1000M speed and negotiate Full/Half duplex mode automatically. These switching ports allow users to connect the Switch to 10Base-T, 100Base-TX and 1000Base-T devices. ?. [. . . ] Fully Flow Control Supported - Full-duplex mode: IEEE 802. 3x - Half-duplex mode: Backpressure 4. Network Status Monitoring LEDs - System: Power - Per port: 1000M, Link/ACT . Filter/Forward Rate - 10Mbps ports ­ 14, 880pps - 100Mbps ports ­ 148, 800pps - 1000Mbps ports ­ 1, 488, 000pps 7. [. . . ]