User manual COMET LABS BARCODE

[. . . ] Be sure that you keep the packing with all accessories contains in the package for your returning of service. Connecting the scanner ­ Keyboard wedge/RS-232C/USB: Connect the 10-pins RS-45 male connector into the bottom of the scanner and you will hear a "click" when the connection is made. 4 Power supply for RS-232C scanner­ There are 3 ways to supplying the power, use external +5V power supply, use optional power cable (KBDC) which taking the power from KB wedge or if the host supports +5V power from pin 9. Switching cable ­ Before removing the cable from the scanner, it is recommended that the power on the host system is off and the power supply has been disconnected from unit. You will head a "click", then gentle on the strainrelief of the cable and it will slide out of the scanner. SG/LG Series SD Series 5 1. 5 Pin Assignment A> Input Port for Mini Decoder DB 9 Male Pin No. [. . . ] Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read. Repeat the steps 1 - 3 to set additional lengths. 32 <Variable> %4 H1 + Fix Length (2 Sets Available) 1. Complete %2 + - / %2 C3 + 33 5. 7 Matrix 25 Parameters A> Check Digit Transmission <Do Not Calculate Check Digit> %0 I N3 Calculate Check Digit & Transmit Calculate Check Digit & Not Transmit %0 I N7 %0 I N5 B> Set Up Code Length To set the fixed length: 1. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read. Repeat the steps 1 - 3 to set additional lengths. 34 <Variable> %4 I 1 + Fix Length (2 Sets Available) 1. Complete %2 + - / %2 C4 + 35 5. 8 CODABAR/NW7 Parameters A> Set Up Start/Stop Characters Upon Transmission ON <OFF> %0 J H1 %0 J H0 B> Transmission Type of Start/Stop <A/B/C/D> <Start> %0 4 VF <A/B/C/D> <Stop> A Start A Stop %0 4 FF %0 4 V1 B Start B Stop %0 4 F1 %0 4 V2 C Start C Stop %0 4 F2 %0 4 V4 D Start %0 4 V8 %0 4 F4 D Stop %0 4 F8 36 C> Set Up Code Length To set the fixed length: 1. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read. Complete %2 + - / %2 C5 + 37 5. 9 Code 93 Parameters A> Check Digit Transmission <Calculate Check 2 Digits & Not Transmit> %0 KN4 Do Not Calculate Check Digit %0 KN3 B> Set Up Code Length To set the fixed length: 1. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read. Repeat the steps 1 - 3 to set additional lengths. 38 <Variable> %4 K1 + Fix Length (2 Sets Available) 1. Complete %2 + - / %2 C6 + 39 5. 10 Code 11 Parameters A> Check Digit Transmission <Do Not Calculate Check Digit> Calculate Check 1 Digit & Transmit %0 L N3 Calculate Check 1 Digit & Not Transmit %0 L N7 %0 L N5 Calculate Check 2 Digits & Transmit Calculate Check 2 Digits & Not Transmit %0 L N6 %0 L N4 B> Set Up Code Length To set the fixed length: 1. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read. Repeat the steps 1 - 3 to set additional lengths. 40 <Variable> %4 L 1 + Fix Length (2 Sets Available) 1. Complete %2 + - / %2 C7 + 41 5. 11 MSI/PLESSEY Code Parameters A> Check Digit Transmission <Do Not Calculate Check Digit> Calculate Check Digit & Transmit %0 NN3 Calculate Check Digit & Not Transmit %0 NN7 %0 NN5 B> Set Up Code Length To set the fixed length: 1. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read. Repeat the steps 1 - 3 to set additional lengths. 42 <Variable> %4 N1 + Fix Length (2 Sets Available) 1. Complete %2 + - / %2 C9 + 43 5. 12 BC 412 Code Parameters A> Check Digit Transmission Do Not Calculate Check Digit <Calculate Check Digit & Transmit> %0 ON3 Calculate Check Digit & Not Transmit %0 ON7 %0 ON5 B> Set Up Code Length To set the fixed length: 1. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read. Repeat the steps 1 - 3 to set additional lengths. 44 <Variable> %4 O1 + Fix Length (2 Sets Available) 1. Complete %2 + - / %2 CA+ 45 5. 13 Code 2 of 6 Parameters A> Check Digit Transmission Do Not Calculate Check Digit <Calculate Check Digit & Transmit> % PN3 0 Calculate Check Digit & Not Transmit % PN7 0 % PN5 0 B> Set Up Code Length To set the fixed length: 1. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read. Repeat the steps 1 - 3 to set additional lengths. 46 <Variable> % P1 + 4 Fix Length (2 Sets Available) 1. [. . . ] Complete %8 3 0 + 59 6. 10 Setup Insertion To setup the insertion of output characters: 1. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the desired position to be inserted. Scan the "Complete" label of "Character Position to be Inserted". Go to the ASCII Tables in Appendix B or Function Key Tables in Appendix C, scan label(s) that represents the desired characters to be inserted. [. . . ]