User manual CISCO ATA 186

[. . . ] Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (H. 323) Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www. cisco. com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Customer Order Number: OL-4008-01 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. [. . . ] Once the web server is disabled, you must configure the Cisco ATA with the TFTP or voice configuration menu methods. Examples 1. If the existing OpFlags value is 0x2, select menu option 323 from the voice configuration menu and enter the value 130 (0x82). If you later attempt to access the Cisco ATA web configuration page, the following error messages will be displayed. ­ Netscape: The document contained no data. ­ Internet Explorer: The page cannot be displayed. 2. If the existing OpFlags value is 0x82, select menu option 323 from the voice configuration menu and enter the value 2 (0x2). This disables web configuration. 8 9 10 11 12-13 14-27 28-31 If Bit 8=1, the Cisco ATA does not allow HTTP refresh access with the http://ip/refresh command. If Bit 9=1, the Cisco ATA does not allow HTTP reset access with the http://ip/reset command. If Bit 11=0, the Cisco ATA requests the device hostname from the DHCP server. If Bit 11=1, the Cisco ATA uses the device hostname that is specified in DHCP option 12. To configure the Cisco ATA to prompt the user for the UIPassword when the user attempts to perform a factory reset or upgrade using the voice configuration menu, configure bits 28 to 31 with the value of 6. Any other value for these bits means that the Cisco ATA will not prompt the user for the UIPassword in these cases. VLANSetting Description This parameter is for firmware version 2. 15 and 2. 14ms, and above. Bitmap definitions are as follows for the VLANSetting parameter: · · · Bits 0-2--Specify VLAN CoS bit value (802. 1P priority) for TCP packets. Bits 3-5--Specify VLAN CoS bit value (802. 1P priority) for UDP packets. Bits 6-17--Reserved. Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (H. 323) 5-34 OL-4008-01 Chapter 5 Parameters and Defaults Optional Feature Parameters · · Bits 18-29--User-specified 802. 1Q VLAN ID. Bits 30-31--Reserved. Value Type Bitmap Default 0x0000002b Voice Configuration Menu Access Code 324 Related Parameter OpFlags, page 5-33 Optional Feature Parameters This section includes the parameters used to configure various timeout values and call-progress tones: · · · · · · NPrintf, page 5-35 RingOnOffTime, page 5-36 IPDialPlan, page 5-36 DialPlan, page 5-37 Call-Progress Tone Parameters, page 5-41 CallCmd, page 5-46 NPrintf Description Use this parameter to specify the IP address and port of a host to which all Cisco ATA debug messages are sent. The program prserv. exe, which comes bundled with the Cisco ATA software, is needed to capture the debug information. Syntax <HOST_IP>, <HOST_PORT> Example If the program prserv. exe is running on a host with IP address 192. 168. 2. 170 and listening port 9001, set NPrintf to 192. 168. 2. 170. 9001. This causes the Cisco ATA to send all debug traces to that IP address. Value Type Extended IP address Default 0 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (H. 323) OL-4008-01 5-35 Chapter 5 Optional Feature Parameters Parameters and Defaults Voice Configuration Menu Access Code 81 RingOnOffTime Description This parameter specifies the ringer cadence pattern, expressed as a triplet of integers "a, b, and c". · · · a--Number of seconds to turn the ring ON. c--The ring frequency, fixed at 25. Value Type List of three integer values, separated by commas Range 1-65535 Default 2, 4, 25 Recommended Values: · · United States --2, 4, 25 Sweden -- 1, 5, 25 Voice Configuration Menu Access Code 929 IPDialPlan Description This parameter allows for detection of IP-like destination address in DialPlan. Three values are valid: · · · 0--String is dialed as is and not treated as an IP address. 1--When the Cisco ATA detects two asterisks (**), IPDialPlan takes over. The user enters the pound (#) key to terminate the digit collection, and the interdigit timeout default is not used. 2--When IPDialPlan is set to 2, three asterisks (***) are required for IPDialPlan to take effect. All other values are currently undefined. Value Type Integer Range 0, 1 or 2 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (H. 323) 5-36 OL-4008-01 Chapter 5 Parameters and Defaults Optional Feature Parameters Default 1 Voice Configuration Menu Access Code 310 DialPlan Description The programmable dial plan is designed for the service provider to customize the behavior of the Cisco ATA for collecting and sending dialed digits. The dial plan allows the Cisco ATA user to specify the events that trigger the sending of dialed digits. These events include the following: · · · · The termination character has been entered. [. . . ] RTP provides services such as payload type identification, sequence numbering, timestamping, and delivery monitoring to real-time applications. Registrar Server router RTP S SCCP SDP Signaling connection control part. SDP messages can be part of SGCP and MGCP messages. Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (H. 323) OL-4008-01 GL-5 Glossary SIP Session Initiation Protocol. Protocol developed by the IETF MMUSIC Working Group as an alternative to H. 323. SIP features are compliant with IETF RFC 2543, published in March 1999. [. . . ]