User manual CASIO XJ-A130V

[. . . ] JEGFSISwChK Z Mode d'emploi (Opérations de base) Conservez la documentation à portée de main pour toute référence future. Conservare l'intera documentazione dell'utente a portata di mano per riferimenti futuri. Instruktionshäfte (Grundläggande anvisningar) Förvara all användardokumentation nära till hands för framtida referens. · · Some models covered by this User's Guide may not be available in certain geographic areas. · Einige der in diese Bedienungsanleitung einbezogenen Modelle sind in bestimmten Gebieten eventuell nicht erhältlich. · Certains modèles couverts par ce mode d'emploi peuvent ne pas être commercialisés dans certaines zones géographiques. · Algunos modelos cubiertos por esta Guía del usuario pueden no estar disponibles en determinadas áreas geográficas. [. . . ] Use the procedure under "Specifying the Display Message Language" on the page E-19 to configure the language settings. NOTE If the Eco Mode is turned on, the LIGHT indicator will light green when the projector is turned on. E-18 Getting Ready Specifying the Display Message Language A "Language" window will be projected the first time you turn on the projector. Use the menu on this screen to specify the display language you want to use. 1. Use the cursor [] and [] keys to highlight the language you want to use. 2. Press the [ENTER] key. E-19 English Getting Ready Turning Off the Projector Caution The projector may remain quite hot for a while after you turn it off. Take care when moving the projector or otherwise handling it after use. See "Precaution when Handling the Projector after Use" (page E-8) for more information. Make sure that the projector is cooled down sufficiently before storing it. To turn off the projector 1. Press the [P] (Power) key. This causes the confirmation message "Do you want to turn off the projector?" to appear in the center of the projection screen. If you do not turn off the projector the confirmation message will disappear automatically after about 10 seconds. The confirmation message will also disappear if you press the [ESC] key. 2. To turn off the projector, press the [P] (Power) key again in response to the confirmation message. This causes the projector light source unit to go out and stops projection. 3. After checking to make sure that the POWER/STANDBY indicator has stopped flashing amber and remains lit, unplug the AC power cord from the power outlet. This causes the POWER/STANDBY indicator to go out. 4. After ensuring that the projector and the connected computer or video device are turned off, disconnect the connecting cables from the projector and the connected device. 5. Close the lens cover. NOTE You can turn off the projector by simply unplugging the power cord without pressing the [P] (Power) key (Direct Power Off). Note, however, that doing so while Zoom Memory (Option Settings 2 Zoom Memory) is enabled will not save the current projection size setting. For more information, see the User's Guide on the CD-ROM that comes with the projector. The projector turns off automatically after a certain amount of time of key operation and input signal inactivity (Auto Power Off). The initial default setting is 10 minutes. E-20 Projector Basics Selecting the Input Source 1. Press the [INPUT] key. This displays the input source selection screen. Turning on the projector initially causes the same input source that was selected the last time it was turned off to be selected. You can perform the following steps to select a different input source. 2. Use the [] and [] keys to select the name of the input source you want to select and then press the [ENTER] key. The name of the input source you select appears in the upper right corner of the projection screen for a few seconds. [. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- -- -- -- Reorient or relocate the receiving antenna. [. . . ]