User manual CASIO XJ-560

[. . . ] E DATA PROJECTOR XJ-460/XJ-560 User's Guide · Make sure you read all of the precautions in the printed "User's Guide (Basic Operations)" first. Also see the "User's Guide (Basic Operations)" for information about setting up the projector and replacing its lamp. · Keep this manual in a safe place for future reference. · · · · Digital Light ProcessingTM, DLPTM, Digital Micromirror DeviceTM, and DMDTM are trademarks of Texas Instruments Incorporated of the United States. Microsoft, Windows, Windows NT, Windows XP, and the Windows logo are registered trademarks or trademarks of Microsoft Corporation of the United States in the United States and other countries. [. . . ] Color balance settings cannot be configured when there is no input signal. A different setting can be configured and is stored for each input source. 32 Using the Setup Menu Adjusting Color Balance by Selecting a Color Temperature Value You can use the procedure below to adjust color balance. A lower color temperature makes whites redder, while a higher color temperature makes them bluer. 1. Use the [ menu, select the "Color Balance" submenu item, and then press the [ENTER] key. This displays the color balance setting screen. ] and [ ] keys to select "Color Temperature", and then press the [ENTER] key. This causes a mark to appear at the beginning of the "Color Temperature" line, which indicates that color temperature value selection is enabled. 3. After the setting is the way you Adjusting Color Balance by Adjusting Color Components Instead of specifying a color temperature to adjust color balance, you can also individually adjust the relative intensity of the red, green, and blue components. 1. Use the [ menu, select the "Color Balance" submenu item, and then press the [ENTER] key. This displays the color balance setting screen. ] and [ ] keys to select "Color", and then press the [ENTER] key. This causes a mark to appear at the beginning of the "Color" line, which indicates that color adjustment is enabled. 33 Using the Setup Menu 3. After all ] and [ ] keys to select the color you want to adjust, and then use the [ ] and [ ] keys to adjust it. Vertical Position IImage Adjustment This sub-menu lets you adjust the vertical position of the input source image within the projection area. "Image Adjustment" main menu item settings are saved for the current signal type only (XGA/60Hz, SXGA/60Hz, etc. ), and not for the input signal source. Note, however, that the number of signal type settings that can be saved is limited. Exceeding the limit causes the oldest setting to be deleted automatically. IImage Adjustment Horizontal Position This sub-menu lets you adjust the horizontal position of the input source image within the projection area. See "Image Adjustment Vertical Position" for details about how settings are saved. IImage Adjustment Frequency This sub-menu lets you manually control the frequency of the image. Normally, the projector is able to adjust the frequency automatically. If there are vertical bands in the projected image, however, it means that automatic adjustment is not possible for some reason. This setting is possible only when RGB is selected as the input source. Note, however, that the number of signal type settings that can be saved is limited. Exceeding the limit causes the oldest setting to be deleted automatically. If, for some reason, your manual frequency settings cause the image input from the computer to disappear from the projection, you can press the [AUTO] key to perform an auto adjust operation (page 8), which should cause the image to reappear. IImage Adjustment Phase This sub-menu lets you manually control the phase of the image. If there are color errors or flickering in the projected image, however, it means that automatic adjustment is not possible for some reason. This setting is possible only when RGB is selected as the input source. See "Image Adjustment Frequency" for details about how settings are saved. 34 Using the Setup Menu IImage Adjustment Noise Filter This sub-menu provides a choice of noise filter levels to remove digital noise from the projected image when RGB is selected as the input source. Note that the noise filter may not be able to remove certain types of digital noise. This setting is possible only when RGB is selected as the input source. [. . . ] See User's Guide (Basic Operation) User's Guide (Basic Operation) 72 Appendix Problem The projector does not project any image from the connected device. Cause and Recommended Action The connected computer or video device may not be turned on, or it may not be outputting a video signal. Make sure the connected computer or video device is turned on, and perform the required operation on it to output a video signal. On the projector, select the input source that corresponds to the device whose image you are trying to project. See -- page 6 The projector does not correctly project the image from the connected device. Images may not project correctly when you have the component output terminal of a video device connected to the RGB terminal of the projector. Try using the projector's VIDEO input terminal or S-VIDEO input terminal (see "Connecting to a Standard Video Device"). [. . . ]