User manual CASIO XJ-450

[. . . ] E DATA PROJECTOR XJ-450 User's Guide Keep this manual in a safe place for future reference. · · · · Digital Light ProcessingTM, DLPTM, Digital Micromirror DeviceTM, and DMDTM are trademarks of Texas Instruments Incorporated of the United States. Microsoft, Windows, Windows NT, Windows XP, and the Windows logo are registered trademarks or trademarks of Microsoft Corporation of the United States in the United States and other countries. Other company and product names may be registered trademarks or trademarks of their respective owners. VCCI B Safety Precautions Safety Precautions Thank you for selecting this CASIO product. Be sure to read these "Safety Precautions" before trying to use it. [. . . ] Press the [KEYSTONE] key. This causes the keystone correction screen to appear on the projected image. 2. Use the [ ] and [ ] keys to select either "Vertical Keystone Correction" or "Horizontal Keystone Correction". 55 Projection Operations 3. Use the [ ] and [ ] keys to correct for keystoning. Each press of [ ] or [ ] shifts the indicator on the currently selected bar left or right. Repeat steps 2 and 3 to perform keystone correction for the other direction, if you want. 4. After the settings are the way you want, press the [ESC] key or the [KEYSTONE] key. This causes the keystone correction screen to disappear. The allowable ranges for manual keystone correction are ­30 to +30 degrees vertically, and ­30 to +30 degrees horizontally. Adjusting the Volume Level (VOL +/­) You can use the remote controller keys to adjust the volume level of the audio that is output from the projector's speaker. To adjust the volume level 1. On the remote controller, press the [VOL +] or [VOL ­] key. This causes the [Volume] screen to appear on the projected image. 2. After the [VOL +] key or the [ ] key to increase the volume, or the [VOL ­] or [ ] key to lower the volume. the setting is the way you want, press the [ESC] key. This causes the [Volume] screen to disappear. 56 Projection Operations Enlarging the Projected Image (D-ZOOM +/­) You can use the remote controller's zoom keys to enlarge a specific part of the projected image up to four times its original size. To enlarge part of the projected image 1. On the remote controller, press the [D-ZOOM +] or [D-ZOOM ­] key. This causes a cross cursor to appear on the projected image. 2. Use the remote controller's cursor keys to move the cross cursor to the part of the image that you want in the center of the enlarged image. 57 Projection Operations 3. On the remote controller, press the [D-ZOOM +] key to enlarge the image. You can press the [D-ZOOM +] key again to further enlarge the image, up to 4 times. You can back step through the image enlargements by pressing the [D-ZOOM ­] key. You can shift the zoomed image up, down, left, or right by pressing the applicable remote controller cursor key. 4. To exit image enlargement and return the image to its original size, press the remote controller's [ESC] key. 58 Projection Operations Using Picture-in-Picture (P-IN-P) While RGB is selected as the input source, you can display a sub-window that simultaneously displays the image being input through the VIDEO or S-VIDEO terminal. This function is called "picture-in-picture" or "P-IN-P". RGB input image VIDEO (or S-VIDEO) input image The initial default setting for the sub-window input source is VIDEO. Use the setup menu when you want to change the sub-window input source to S-VIDEO. Note that P-IN-P can be used only when RGB is selected as the input source. If Component is selected for "Input Settings RGB Input" on the setup menu, you need to change the setting to RGB in order to use picture-in-picture. Note that the initial default setting for "Input Settings RGB Input" is RGB. 59 Projection Operations To display the sub-window 1. On the remote controller, press the [RGB] key to select RGB as the input source. You can also select the input source using the projector's [INPUT] key. the remote controller, press the [P-IN-P] key to display the subwindow. This causes the sub-window, containing the image input through the VIDEO or S-VIDEO terminal, to appear on the projected image. The sub-window will be located at the position that was used the last time a sub-window was displayed. You can leave the sub-window where it is, or move it to another location within the projected image. See "To change the location of the sub-window" for more information. [. . . ] See page 41 120 -- 48 39 89 122 Troubleshooting Problem When RGB/Component is selected as the input source, the color of the projected image or the image itself is abnormal. Cause and Recommended Action The settings configured on the setup menu's "Input Settings RGB Input" menu may not be compatible with the device connected to the RGB input terminal. Use the setup menu to configure the "Input Settings RGB Input" menu settings to correct the problem. Make sure the remote controller is within the allowable range when you operate it. See page 89 The projector keys to not work. The remote controller does not work. 94 27 29 The auto keystone correction function (AF/AK) does not work correctly. The sensors may have finger smudges or dirt on them. [. . . ]