User manual CASIO QW-373

[. . . ] START STOP START STOP RESET ENGLISH Time Display Day of the week Lap counter Year Month Day Second Hour Hours Minute Timekeeping Mode Stopwatch Mode Seconds Minutes 1/1000th of a second Recall Mode Total elapsed time Lap time Split time Stopwatch Display NORMAL TIME START STOP RESET Auto Return The stopwatch returns to the Timekeeping Mode if left unused for a few minutes. USING THE TIMER You can set start times for up to 10 intervals, which are counted down in sequence one after the other. You can configure the timer interval sequence to repeat up to 100 times. · When the timer sequence reaches the end of the final interval, it restarts from the beginning of the first interval. CHART 0 a (a) To time a match BUTTON OPERATION Current time Number of repeats Timer number Timer start time DISPLAY PM NET TIME START STOP START STOP RESET CHART 0 a (a) (a) (Stoppage time) b (a + b) Example: Timer 1 20'00" Timer 2 10'00" Timer 3 05'00 Repeat 2 CHART Timer 1, Repeat 1 start Timer 1 end, Timer 2 start Timer 2 end, Timer 3 start 0 a (a) (a) (Stoppage time) b (a + b) BUTTON OPERATION BUTTON OPERATION Timer 3 end Timer 2 end, Timer 3 start Timer 1 end, Timer 2 start Timer 3 end, Timer 1 start DISPLAY DISPLAY CARE OF YOUR STOPWATCH After stopping a net time operation by pressing C, you can resume it by pressing C again. LAP/SPLIT TIMES START 1ST LAP STOP 2ND LAP 3RD LAP RESET To set an interval start time · This stopwatch is water resistant up to five bars (atmospheres), which means you can use it in the rain or in areas where splashing water is present. Never, however, operate the buttons of the stopwatch while it is immersed in water. [. . . ] · Should moisture appear inside the stopwatch, have it checked immediately by your dealer or a CASIO distributor. 0 CHART Football Stopwatch Mode Counter Mode Alarm Mode Timer Mode a (a) b (a + b) c (a + b + c) (t) Reset Timer Selection SPECIFICATIONS Accuracy at a normal temperature (TIME): ±30 seconds per month (STOPWATCH): 99. 9988% Display capacity: · Time Display: Hour, minutes, seconds, am/pm, year, month, day and day of the week Calendar system: Pre-programmed until the year 2099 · Stopwatch Display: Measuring capacity: (Total elapsed time display) 9 hours 59 minutes 59. 999 seconds (Lap time display) 59 minutes 59. 999 seconds (Split time display) 9 hours 59 minutes 59. 999 seconds Measuring unit: 1/1000 second Measuring modes: Net time, lap time, split time, 1st-100th place time, lap counter (up to 99) Memory capacity: 2 sets of 100 records each Timer 10 intervals Measuring capacity: 59 minutes 59 seconds Measuring unit: 1 second Number of repeats: 100 Beeper duration: 10 seconds Alarm Number of alarms: 12 Beeper duration: 10 seconds Setting unit: 1 minute Counter Standard Counter: 0 to 99999 Stopwatch Counter: 0 to 99999 Measuring capacity: 59 minutes 59 seconds Dual Counter: 0 to 99999 Football Stopwatch Measuring capacity: 59 minutes 59 seconds Measuring unit: 1 second Beeper duration: 10 seconds Battery: One lithium battery (type: CR2032) Approx. 5 years continuous operation on type CR2032 (includes an average of 30 presses of button per day. ) Operating Temperature: 0°C to 40°C (32°F to 104°F) 1ST SPLIT (a) 2ND SPLIT (a+b) 3RD SPLIT (a+b+c) BUTTON OPERATION Timer Interval Setting Repeat Setting DISPLAY · A sticker is affixed to the glass of this stopwatch when you purchase it. · Depending on its model, the configuration of your stopwatch may differ somewhat from that shown in the illustration. MULTIPLE FINISHING TIMES Example : To record the times of 100 different runners. START 1ST RUNNER FINISHES 2ND RUNNER FINISHES 99TH RUNNER FINISHES 100TH RUNNER FINISHES RESET 1. In the Timer Mode, hold down the R button for about 2 seconds until the displayed interval time starts to flash. Use the C and A buttons to scroll through the 10 interval times until the one you want to change is displayed. · Interval timers count down in sequence from Timer 1 to Timer 10. Use the B button to move the flashing between the minute and second digits. · You can specify a start time within the range of 0 to 59 minutes 59 seconds. · You can repeat steps 2 and 3 to set other interval timer start times, if you want. · Starting a new stopwatch elapsed time operation will cause the older of the two record groups to be deleted automatically in order to make room for a new group of records. · There is also a FAST LAP record that displays the fastest lap from among all of the lap times currently in memory. · Record 1 (the newest record) will always be displayed first whenever you press the R button to switch from the Stopwatch Mode to the Recall Mode. · In the Recall Mode, each press of the B button will toggle the display between record group 1 and record group 2. · Lap time records in memory can be recalled while an elapsed time operation is in progress or stopped. · Memory records are cleared whenever a new Stopwatch Mode elapsed time operation is stared by pressing the C button after pressing the A button to reset the stopwatch to all zeros. Holding down the or button scrolls at high speed. In the Alarm Mode, hold down the A button until "ALL OFF" appears on the display. This turns off all 12 alarms. To test the alarm Hold down the C button to sound the alarm. To set the alarm time 1. In the Alarm Mode, use the C button to scroll through the alarm screen (1 through 12), until the one you want to set is displayed. Hold down the R button for about 2 seconds until the hour digits of the alarm time start to flash. [. . . ] Hold down the R button for about 2 seconds until the hour digits of the alarm time start to flash. Use the B button to move the flashing between the hour and minute digits. Use the C (+) and A (­) buttons to change the currently flashing digits. After the setting is the way you want, press the R button to exit the setting screen. [. . . ]