User manual CASIO QV-7000SX

[. . . ] QUICK REFERENCE LCD Digital Camera QV-7000SX Owner's Manual Loading Batteries (page 27) Be sure to load the four AA size batteries that come with the camera before using it. 1 3 1 LOCK 2 1 3 LOCK 2 On the bottom of the camera, slide the battery compartment cover lock towards the front of the camera (1) to release the cover. 1 Grasping both sides of the battery compartment cover, swing it open (2 3 2 3). 2 Load batteries so their plus (+) and minus (­) ends are facing as shown in the illustration. Close the battery compartment cover (1 2 ), and then slide 1 the battery compartment cover lock towards the back of the camera to lock the cover in place (3). 3 If you need help with your camera, please call: 1(800)435-7732 · Be sure to use alkaline, lithium or Ni-MH batteries. [. . . ] The procedures for changing current settings can be found on the pages noted in the table. DIGITAL ZOOM FLASH AF/MF/MACRO 3. Press MENU to start manual white balance setting. · Keep the camera pointed at the white piece of paper. · Pressing the shutter button at this time returns the camera to the white balance setting that was obtained the last time you performed this manual white balance procedure. MODE MEMORY and then press the shutter button. 4. Use [+] and [­] to select the item you want, and then press the shutter button to toggle it on and off. · Turning an item on stores its current setting in mode memory when the camera is turned off, while turning an item off tells the camera to use its preset default setting. 6. The manual white balance procedure stops automatically when it is done. · If the manual white balance procedure does not end automatically, press the shutter button to interrupt it. 63 64 OTHER RECORDING FUNCTIONS OTHER RECORDING FUNCTIONS Item WB APERTURE DIGITAL ZOOM FLASH AF/MF/MACRO METERING Initialized Setting OFF OFF OFF ON OFF ON 5. After the on/off status of each item is the way you want it, press MENU. Initializing Mode Memory Use the following procedure to initialize the mode memory. To initialize mode memory 1. Align the dial with . · An item that is ON stores its current setting in mode memory when camera power is turned off, and restores the setting when power is turned back on again. · An item that is OFF uses the camera's preset power on default setting. 3. Use [+] and [­] to select MODE MEMORY, and then press DISP to initialize mode memory. · The following table shows the mode memory status of each item following the above procedure. 65 66 PLAYBACK The following describes the different techniques that you can use to playback recorded images. PLAYBACK PLAYBACK Playing Back a Movie Use the following operation to play back a movie that was recorded using the operation under "Movie Recording" on page 50. NOTES · Sliding the Function Switch to PLAY immediately after recording an image displays the image you just recorded first. · Pressing the shutter button while a movie or panorama image is on the monitor screen starts playback of the movie or panorama . · The image that initially appears on the monitor screen in the PLAY mode is a preview image. The full of image appears after a few seconds. · While movie playback is paused, you can use [+] (forward) and [­] (reverse) to move frame-by-frame through the movie. Basic Playback Operation The built-in monitor screen of the camera lets you play back recorded images without connecting an external monitor. 4. Slide the Function Switch to PLAY. REC PLAY · The PLAY position selects the Playback Mode, while REC selects the Record Mode. 3. Press the shutter button to start playing back the movie. · You can use [+] (forward) and [­] (reverse) while playing back a movie to change the playback direction. · To enlarge the movie image so it fills the entire monitor screen, press DISP. · Pressing the shutter button during movie play pauses playback. Use [+] and [­] to scroll through the images stored in camera memory. · Press [+] to scroll forward and [­] to scroll back. Holding down either button scrolls at high speed. 67 68 PLAYBACK PLAYBACK Regrouping Movie Images When you record a movie, the camera automatically groups four images that make up the movie. Transferring a movie to a personal computer causes its images to become ungrouped. If you download the movie back to the camera, you will be unable to play it back as a movie unless you use the following procedure to re-group the images. 3. Use [+] and [­] to select MOVIE, and then press the shutter button. To ungroup movie images 1. [. . . ] Light Metering: Multi-pattern/spot metering by CCD Exposure: Program AE, aperture priority AE Exposure Compensation: ­2EV to +2EV (1/4EV units) Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 to 1/1000 second (1 second in Night Mode) Aperture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2. 8 to F14 automatic and manual switching White Balance . . . . . . . . . . . . . . . . . . . . Automatic, fixed (4 modes), manual switching Self-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]