User manual CASIO PRIVIA PX-3S

[. . . ] Guarde toda documentación para futuras consultas. Safety Precautions Before trying to use the piano, be sure to read the separate "Safety Precautions". Precauciones de seguridad Antes de intentar usar el piano, asegúrese de leer las "Precauciones de seguridad" separadas. PX3ES1C Español USER'S GUIDE GUÍA DEL USUARIO English TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT SAFETY INSTRUCTIONS 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Registration memory has eight banks, each of which is divided into eight areas. Registration Data The following are the settings that are stored as registration data when you save a Digital Piano setup. · Layer ON/OFF · Split ON/OFF · Split point · Reverb ON/OFF · Reverb type · Chorus ON/OFF · Chorus type · Each zone tone number · Each zone INT/EXT ON/OFF · All common parameters (page E-18) · All zone parameters (page E-28) · Following function menu items (page E-38) · Touch Response · Pedal Assign · Temperament type · Temperament key note · Stretch Tuning · Acoustic Resonance ON/OFF · Half Pedal Effect NOTE To save a setup as registration data 1. This is the REGISTRATION mode. Lit Bank number · The Digital Piano's current mode (MASTER CONTROL, CARD PLAYER, ZONE EDIT) is not included in registration data. This means that the Digital Piano's mode does not change when you recall registration data. · The following function menu settings are not included in registration data. You can, however, perform the backup operation (page E-40) to retain these settings when the Digital Piano is turned off. · Tuning · EQ Hold · Display Contrast · Song MIDI Out · Song Volume · Song Pre-count · Song Repeat · The backup operation (page E-40) saves all of the above function menu settings, as well as all of the settings that are included in registration data. 3. Use the bt (w, q) buttons to scroll through the banks (1 to 8) until the bank where you want to save the registration data is displayed. E-34 Using Registration Memory 4. ck cl cm cn co cp cq cr dm 2. Use the bt (w, q) buttons to scroll through the banks (1 to 8) until the one you want to rename is displayed. · This displays a screen for editing the name. · Pressing a number button immediately executes the registration data save operation. · The following shows how the display would appear if you select Bank 1, Area 3. Area number Bank number 3. Edit the name. · The initial default name of all the banks is "REGIBANKNAME". · Use the ct (u) and dk (i) buttons to move the cursor left and right, and the bt (w, q) buttons to scroll through characters at the current cursor position. The following shows the characters that can be used in a name. To recall a setup saved as registration data 0 A K U ( 123 BCD LMN VWX )-^ 4 E O Y { 56 FG PQ ZS }@ 7 H R & ~ 8 I S _ ` 9 J T ' 1. Use the bt (w, q) buttons to scroll through the banks (1 to 8) until the one where the registration data you want to recall is displayed. Press one of the number buttons (ck (1) through cr (8)) to specify the number of the area (1 to 8) where the registration data you want to recall is located. · Pressing a number button immediately recalls and applies the setup in accordance with the registration data being recalled. · The following shows how the display would appear if you select Bank 3, Area 7. · You can specify up to 12 characters for a bank name. 4. 5. After the name is the way you want, press the dl (ENTER) button. In response to the confirmation message ("Sure?") that appears, press the bt (YES) button to apply the change or the bt (NO) button to return to the screen in step 3 of this procedure without changing anything. 3. NOTE · To display a bank name, hold down the br (REGISTRATION) button on the registration mode screen. E-35 English While holding down the dm (STORE) button, press one of the number buttons (ck (1) through cr (8)) to specify the number of the area (1 to 8) where you want to save the registration data. To rename a registration memory bank 1. While holding down the bs (FUNCTION) button, press the br (REGISTRATION) button. Using Registration Memory Saving Registration Memory Bank Data to a File Registration data can be stored to a file in the Digital Piano's internal memory area or on an SD card. You can store the registration data in a single registration memory bank (eight areas) or the data in all of the registration memory banks (64 areas) to a file. NOTE 3. Depending on the type of operation you want to perform, use the ct (u) and dk (i) buttons to display one of the screens shown below. To save the data in a single bank · When you save registration memory bank data to a file, a file name is assigned automatically in accordance with the following rules. · If you save the data in a single bank, the file name will be in the format: <first 6 characters of bank name><2-digit number specified by you>. CB6. · If you save the data in all the banks, the file name will be in the format: <REGIST><2-digit number specified by you>. CR6. · Before saving registration memory bank data to an SD card, be sure to first read the important information contained in the following sections of this user's guide. · "Card and Card Slot Precautions" (page E-46) · "To load and remove a memory card" (page E-46) · "To format a memory card" (page E-46) To save the data in all banks 4. 5. Use the bt (w, q) buttons to specify the two-digit number you want to append to the name of the file. · The message "Replace?" will appear if a file with the same name already exists. [. . . ] 3 : Level (0 to 127) Adjusts the output level. E-62 Appendix 15: Auto Wah Multi-effect Algorithms A multi-effect is one connected to multiple single effects (page E-61). "M01: Multi01 (Enhancer - Chorus)", for example, is a multi-effect connected to two single effects: Enhancer and Chorus. The parameters included in a multi-effect algorithm are the same as the each of the connected single-effect algorithms. However, the following two parameters are specific to multi effects. This is a "wah" effect that can automatically shift the frequency in accordance with the level of the input signal. [. . . ]