User manual CASIO KL-8700

[. . . ] Immediately turn power off and unplug the power cord from the wall outlet. AC adaptor · Do not allow the power cord to become damaged or broken, and never modify, over bend, twist, or pull it. Never place heavy objects on the power cord, and never expose it to direct heat. Use of another AC adaptor creates the danger of fire and electrical shock. [. . . ] Indicator A A Meaning Normal Bold Outline Indicator Meaning Shadow Raised 3. Move the cursor to the end block up to which you want to change the text effect and then press SET to register your selection and change the effect. · At this point, the label printer returns to the text input screen. To change the text effect for lines of text TEXT This range is used to specify text across various lines, etc. · A TEXT range specification must begin and end with in the same block. A 1 a B 2 b C 3 c D 4 5 A A A A Text Effects You get a choice of three text effects: shading, underline, and box. The text effects are applied to text on the display, in addition to the printed text. To assign text effects 1. While there is text on the display, press EFFECT. ­ ­ ­ ­ E F F EC T ­ ­ ­ ­ S H A D I NG UNDER L I NE BOX 1. After performing the two steps under "To assign text effects", use u and i to highlight "LINE" and then press SET. Move the cursor to the start line from which you want to change the text effect and then press SET to register your selection. Move the cursor to the end line up to which you want to change the text effect and then press SET to register your selection and change the text effect. · At this point, the label printer returns to the text input screen. To change the text effect for specific characters 1. After performing the two steps under "To assign text effects", use u and i to highlight "CHARACTER" and then press SET. I Small Typeface Horizontal Factor 1 2 3 4 5 6 7 8 Small Typeface 2. Use u and i to highlight "SIZE" and then press SET. ­ ­ ­ ­ ­ S I ZE ­ ­ ­ ­ ­ H E I GH T W I DTH Standard Typeface · The normal size for the standard typeface is 1 × 1 (24 × 24 dots; 3mm × 3mm). · Character size can be changed by specifying a vertical factor (1, 2, 3, 4, 5) and a horizontal factor (1, 2, 3, 4, 5, 6, 7). · The table below shows the character size indicator values that appear for each character size. 4×4 3. · Use t and y to move the highlighting between the two dimensions. · To change a dimension, press i to increase it or u to decrease it. Or you can input a value directly on the label printer's keyboard. · Remember that the dimensions you can specify depend on the width of the tape loaded in the label printer (see table, left). After you finish setting the character size you want, press SET to register it. ­ ­ ­ ­ ­ S I ZE ­ ­ ­ ­ ­ F RO M ? Vertical 1 2 3 1×1 1×2 1×3 1×4 1×5 1×6 1×7 1×8 2×1 2×2 2×3 2×4 2×5 2×6 2×7 2×8 3×1 3×2 3×3 3×4 3×5 3×6 3×7 3×8 4×1 4×2 4×3 4×4 4×5 4×6 4×7 4×8 12345 E-14 4 5. Move the cursor to the start character from which you want to change the character size and then press SET to register your selection. ­ ­ ­ ­ ­ S I ZE ­ ­ ­ ­ ­ TO ? 24mm and 18mm tape, 2 lines of text 1 × 1/1 × 1 2 × 2/1 × 1 1 × 1/3 × 3 1 × 1/2 × 2 2 × 2/2 × 2 3 × 3/1 × 1 3. Use u, i, t and y to move the highlighting to the format that you want to use and then press SET to select it. [. . . ] Possible Cause Ink ribbon cassette loaded while the ink ribbon is slack. Action Remove the ink ribbon cassette and check to make sure the ink ribbon is not broken. Next, take up any slack in the ink ribbon and then reload the tape cartridge. · Before loading an ink ribbon cassette into the label printer, always make sure you take up any slack in the ink ribbon first. [. . . ]