User manual CASIO KL-820

[. . . ] E KL-820 User's Guide RJA519067-001V01 Read This First! · CASIO COMPUTER CO. , LTD. shall not be held liable for any loss or claims by you or any other person or entity that may arise through the use of this printer. · Reproduction of this manual in any form, either in part or its entirety, is forbidden without the express permission of CASIO COMPUTER CO. , LTD. · The contents of the manual are subject to change without notice. [. . . ] · Number of text lines (page E-13) · Text alignment (page E-23) · Character pitch (page E-23) The block mark is located here. 3 cm 4´4 P r omo t i o n P l a n B Re t a i l Pa c k a g e · · Block 1 Block 2 · Two lines (page E-13) · To delete a block mark, move the cursor to the B symbol, and then press DEL. · You can have up to three blocks inside of a single tape label layout. Simply move the cursor to the location where you want to input a block mark, and then press FUNC . · Block marks cannot be input when FIX is selected for TAPE LENGTH. · The frame function cannot be used when there are a block mark input. Example To layout "Promotion Plan" and "Retail Package Sample Data" as separate blocks within the same tape label 1. · This inputs a "block mark, " which makes the text to the left of a block. a b 1 4 . 7 cm 4´4 P r omo t i o n P l a n B · · · · · · · · · · · · · · · · Block mark Block marks appear on the display only. They are not printed on the tape. E-15 Part 4 Deleting and Inserting Characters To delete characters using the DEL key Example: To change the word "commmputer" to "computer". Use c and v to move the cursor under the first (far left) "m". Press DEL twice to delete the two m's at the cursor's position, shifting "mputer" to the left as you do. Press FUNC and then v to jump back to the end of the characters for more input. This section describes everything you need to know about deleting and editing characters you have already input. Moving the Cursor Use the cursor keys to move the cursor around the display and position it for deleting and editing characters. Clearing the Display Use the following procedure to clear all input text from the display. To move the cursor · Press c to move the cursor to the left, and v to move the cursor to the right. · Press x to move the cursor to the up, and z to move the cursor to the down. · Press FUNC and then c to make the cursor jump to the beginning (far left) of the characters on the display. · Press FUNC and then v to make the cursor jump to the end (far right) of the characters on the display. · Holding down the c, v, x or z cursor key moves the cursor at high speed. To clear the display Press FUNC and then DEL (CLS). SET/ESC" appears on the display to confirm that you want to clear the display. Press SET to clear or ESC to abort the operation without clearing anything. Text Editing You can use the following procedures to edit text on the display. Deleting Individual Characters You can delete individual characters with either the BS key or the DEL key. The only difference between the operation of these two keys is the location of the cursor. To insert new characters Example: To change the text "ABCDEF" to "ABCXYZDEF". With the original text on the display, move the cursor under the letter "D". · Inputting the new characters causes them to be inserted at the cursor position. The existing characters are opened up to make room for the new characters. To delete characters using the BS key Example: To change the word "CASSSIO" to "CASIO". [. . . ] Action Peel the backing paper from the back of the tape to expose the adhesive. Labels do not adhere well to surfaces that are rough, wet, oily, or dirty. You can then decrease the number of characters, change to a longer tape setting, or select auto tape length. E-34 Message Possible Causes Action Message LOAD A TAPE CARTRIDGE 18mm OR WIDER CLEARS TAPE LENGTH SETTING SET/ESC Possible Causes Action NO INPUT TEXT!· You are attempting a print · Input the text and then or preview operation try again. [. . . ]