User manual CASIO KL-750

[. . . ] 2 General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Label Printer Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 English Part 2 Getting Ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Be sure to use the following procedure to tell the Label Printer when you are using 6mm tape. NO! · Make sure that the tape does not extend too far past the tape guide. If it does, cut off the end with a pair of scissors. To specify 6mm tape width 1. Press H J K or L to change the setting shown on the display between ON (6mm tape) and OFF (other tape width). When the tape width setting is the way you want it, press SET to register it. · The tape width you set remains in effect until you change it, press ON or reset the Label Printer's memory. E-6 Part 3 Inputting Characters and Symbols This part of the manual tells you how to input characters. To make things easier to understand, we call everything you input a character, regardless of whether it is actually a letter, number, or symbol. Explanations here all use the default settings that are in effect from the initial power-on screen. For information on using other character styles, effects and sizes, see page 10. Further input becomes impossible after you input the 63rd character. · Shift indicator This indicator appears when you press the SHIFT key. While this indicator is on the display, the keyboard is shifted, so the letter keys input upper-case alpha characters. The number keys input the punctuation symbols marked in the upper right corners of the keys. · A newline operation is indicated on the display by the ¥ symbol. For details on printing, see page 11. About the CODE key. . . The CODE key makes it possible to input punctuation needed for a number of different languages. The following shows the key operations you should use for each of the characters formed using the CODE key. Key Operation CODE CODE CODE CODE CODE CODE CODE U O P A S* J K Input Ü OE Å Æ ß Ö Ä Key Operation CODE CODE CODE CODE CODE CODE CODE L Z C N 1 2 3 Input J W Ç Ñ ´ ` ¨ Key Operation CODE CODE CODE CODE CODE CODE CODE 4 5 6 7 8 9 0 Input ~ ^ ° / Basic Alpha-Numeric Input The following operation shows you the basic procedures for inputting letters and numbers. We will explain the procedure by inputting the following characters using the default initial power-on screen. ABXYZ Computer Company 1234567890 Note · If you hold down any key, it will repeat its operation or input at high speed until you release it. * Lower case only. CODE 1 A Special Symbols You can also access a menu of special symbols by pressing FUNCTION 4 (SYMBOL). To input special symbols To input alpha-numeric characters 1. · To input the upper-case letters, you can use either SHIFT or CAPS. With CAPS the keyboard stays in upper-case until you press CAPS again. With the cursor at the location where you want to input a special symbol, press FUNCTION 4 (SYMBOL). · The symbol that is underlined on the display is the one that is currently selected. , . : ; 2. Use the H J K and L cursor keys to move the underlining to the symbol you want. [. . . ] The tape cutter blade is designed to provide approximately 3, 000 cuts. Use the following procedure to replace the blade whenever it starts to cut poorly. To replace the tape cutter blade 1. Open the tape cartridge compartment cover. E-14 · If there is a cartridge already in the Label Printer, remove it by grasping the cartridge on both sides with your thumb and forefinger, and lift straight up. 4. Use a cotton swab dipped in alcohol to clean the printer head and roller as shown in the illustration. Printer head 3. [. . . ]