User manual CASIO KL-120

[. . . ] E KL-120 User's Guide RJA518623-001V01 Read This First! · CASIO COMPUTER CO. , LTD. shall not be held liable for any loss or claims by you or any other person or entity that may arise through the use of this printer. · Reproduction of this manual in any form, either in part or its entirety, is forbidden without the express permission of CASIO COMPUTER CO. , LTD. · The contents of the manual are subject to change without notice. [. . . ] With CAPS the keyboard stays in upper-case until you press CAPS again. · If you input a wrong character, press BS to delete it and input again. When you reach the end of a line of text, press to input a newline mark. · A newline operation is indicated on the display by the symbol. · The maximum number of lines you can input depends on the width of the tape you have loaded in the Label Printer. Tape Width Maximum Number of Lines · 6mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . For details on printing, see page E-18. CAPS off Key Operation CODE CODE CODE CODE CODE CODE CODE U O P A S J K Input ü oe å æ ß ö ä Key Operation CODE CODE CODE CODE CODE CODE CODE L Z C N 1 2 3 Input j w ç ñ Key Operation CODE CODE CODE CODE CODE CODE CODE 4 5 6 7 8 9 0 Input ´ ` ¨ ~ ^ ° / Example: To input á. Press A. About the CODE key. . . The CODE key makes it possible to input punctuation needed for a number of different languages. The following shows the key operations you should use for each of the characters formed using the CODE key. CAPS on Key Operation CODE CODE CODE CODE CODE CODE CODE U O P A J K L Input Ü OE Å Æ Ö Ä J Key Operation CODE CODE CODE CODE CODE CODE CODE Z C N 1 2 3 4 Input W Ç Ñ Key Operation CODE CODE CODE CODE CODE CODE 5 6 7 8 9 0 Input Special Symbols You can also access a menu of special symbols by pressing SYMBOL. (There are a total of 86 different symbols. ) To input special symbols 1. With the cursor at the location where you want to input a special symbol, press FUNC and then 4 (SYMBOL). · The symbol that is underlined on the display is the one that is currently selected. ´ ` ¨ ~ ^ ° / , . ` ' " " , , << >> ¿ ¡ ( ) [ ] { } < > << >> / \ $ ¢ £ Fr 2. Use the c, v, x and z cursor keys to move the underlining to the symbol you want. · This returns to the input screen, with the symbol you selected input at the location where the cursor was located when you displayed the symbol list. E-12 Using Text Blocks In the example label shown below, "Promotion Plan" and "Retail Package Sample Data" are independent units called "text blocks, " or simply "blocks. " You can divided your tape label text into blocks and then apply the following settings on a block-by-block basis. · Number of text lines (page E-12) · Text alignment (page E-19) · Character pitch (page E-19) The block mark is located here. · Here we will input "Retail Package". P r omo t i o n P l a n B Re t a i l Pa c k age · · · To delete a block mark, move the cursor to the B symbol, and then press DEL. · You can have up to three blocks inside of a single tape label layout. Simply move the cursor to the location where you want to input a block mark, and then press FUNC . · Block marks cannot be input when FIX is selected for TAPE LENGTH. See "CLRS TAPE LNGTH SET/ESC" (page E-27) in "Error Messages/Display Messages" for more information. Block 1 Block 2 · Two lines (page E-12) Example To layout "Promotion Plan" and "Retail Package Sample Data" as separate blocks within the same tape label 1. [. . . ] the label to exceed the 6mm tape. . . 1 line maximum number of lines 9mm tape. . . 1 line for the tape you are 12mm tape. . . Up to 2 lines using. 18mm tape. . . Up to 2 lines · You are attempting to recall text from memory when there is none stored. · Store the text in memory and then try again. Printed text is cut off by tape cut operation. Possible Causes Out of tape Action Replace the tape cartridge with a new one. [. . . ]