User manual CASIO EXILIM EX-ZR100

[. . . ] E Digital Camera User's Guide Thank you for purchasing this CASIO product. · Before using it, be sure to read the precautions contained in this User's Guide. · Keep the User's Guide in a safe place for future reference. · For the most up-to-date information about this product, visit the official EXILIM Website at http://www. exilim. com/ To go to "Getting the Most Out of Dynamic Photo" click here! Unpacking As you unpack your camera, check to make sure that all items shown below are included. [. . . ] White Balance, Brightness, Trimming, Rotation, Resize 105 Viewing Snapshots and Movies Zooming an On-screen Image 1. 2. In the PLAY mode, use [4] and [6] to scroll through the images until the one you want is displayed. Slide the zoom controller towards z ([) to zoom. Zoom factor Image area You can use [8], [2], [4], and [6] to scroll the zoomed image on the monitor screen. ­ When monitor screen contents are turned on, a graphic in the lower right corner of the screen shows what part of the zoomed image is currently displayed. ­ Though the maximum image zoom factor is 8X, Current display area certain image sizes may not allow zooming up to the full 8X. · Pressing [SET] will lock the current zoom factor for the on-screen image. You can then use [4] and [6] to scroll between images, using the same zoom factor. Pressing [SET] again will unlock the zoom factor and allow you to use [8], [2], [4] and [6] to move around the currently displayed images. Also, CS group images and movies will not appear when you are scrolling images with [4] and [6]. Displaying the Image Menu 1. In the PLAY mode, slide the zoom controller towards w (]). Use [8], [2], [4] and [6] to move the selection boundary around the image menu. To view a particular image, use [8], [2], [4], or [6] to move the selection boundary to the image you want and then press [SET]. · In the case of a movie or a continuous shutter (CS) file, the first frame of the file will be displayed. Boundary 106 Viewing Snapshots and Movies Viewing Snapshots and Movies on a TV Screen 1. Use the AV cable that comes with the camera to connect it to the TV. AV cable (bundled) Terminal cover TV Video Audio Yellow White Red [USB/AV] port AUDIO IN jack (red) AUDIO IN jack (white) VIDEO IN jack (yellow) Making sure that the 6 mark on the camera is aligned with the 4 mark of the AV cable connector, connect the cable to the camera. · Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction. · Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration. · Make sure that the camera is turned off before plugging in or unplugging the cable. Check the user documentation that comes with the TV for information about requirements before plugging into or unplugging from the TV. 2. Turn on the TV and select its video input mode. If the TV has more than one video input, select the one where the camera is connected. 107 Viewing Snapshots and Movies 3. Press [p] (PLAY) to turn on the camera. This will cause an image to appear on the TV screen, without anything appearing on the camera's monitor screen. · Pressing [ON/OFF] (Power) or [r] (REC) will not turn on the camera while the AV cable is connected. · You also can change the aspect ratio of the screen and the video output system (page 163). 4. Now you can display images and play back movies as you normally do. IMPORTANT! · Before connecting to a TV to display images, be sure to configure the camera's [r] (REC) and [p] (PLAY) buttons for "Power On" or "Power On/Off" (page 162). When you first start displaying images, set the TV volume control at a relatively low level and then adjust it as required. NOTE · Audio is stereo. · Some TVs may not be able to output images and/or audio correctly. · All icons and indicators that appear on the monitor screen also appear on the TV screen. You can use [8] (DISP) to change the display contents. 108 Viewing Snapshots and Movies Viewing High-quality Movies on a Hi-Vision Television Use a commercially available HDMI cable to connect the camera to the TV. For information about playback, see the procedure starting from step 2 under "Viewing Snapshots and Movies on a TV Screen" on page 107. [. . . ] · The term "built-in subjects" refers to the moving figures and characters that came pre-programmed in the camera's built-in memory. Background Image Built-in Subject Dynamic Photo Image 2 Dynamic Photo!A totally new way to enjoy digital photography! Creating a Dynamic Photo Image Your digital camera comes with a number of subjects in its built-in memory ("built-in subjects"). You can use these built-in subjects to create Dynamic Photo images by inserting them into your original snapshots or movies. Step 1: Shoot the image into which you want to insert an built-in subject. In the REC mode, compose the image and press the shutter button to shoot a standard snapshot. You will insert the built-in subject into the snapshot you shoot here. Step 2: Create the Dynamic Photo image. Now simply insert a built-in subject into the snapshot or movie you shot in step 1 to create your own original Dynamic Photo image. 1. [. . . ]